Search results

Hi..... T2 manual available for download from this site free :thumb2:thumb2 Am sure Briggie will post the link but try the downloads section?

I run 50/50 in the summer months (when it is warmer) and checked the Gov website and although a bit vague, 2500 ltrs or less is tax free !!! Copied paragraphs below.......... Here is the link to the HMRC site.... sections 3.4, 4.2 & 4.9 seem to apply...

Bought from Milners so hope they last longer than 3 weeks :thumb2 I have also given the threads a liberal coating of grease to aid future removal and yes... hindsite is a wonderful thing but was my first time:doh.... remove said ARB first then attack whats left of the links with the biggest...

Interesting!!!!! So where can I get some from and will it be ok with my 50/50 diesel/veggie oil??? :naughty

So today I had to change the ARB drop links ready for the MOT this weekend. What a bugger of a job :eek::eek:... off side one was so knackered it fell apart as soon as I tried to undo it!!! Think it was an origional part?.... took an hour with lots of wd40 and an air hammer to get it off the...

rear wash on 2002 truck.... just push the wiper switch forward and hold there.... should then wash and wipe :thumb2

Does anyone know if the 2002 terrano has a dimmer for the dash lights? mine all seem to work but are so dim in the day/half light you cannot see they are on

Hi & welcome.... as stated above re rusty bits and diff..... an 02/3 plate will likely be a fixed hub model so no worries about the springs in the auto hubs! check it works in 4WD..... not the most economical of vehicles but good fun to drive! Water pumps can go but easy enough to fix... my 02...

I suspect the stub axles are all the same across the range.... my 'fixed' hub mk4 looks exactly the same as the manual except no free wheel hub assembly, just the big old fixed flange bit... I cannot believe the parts are different across the different marks...so I would say all major bits are...

The only bit I can think of which is threaded is the actual wheel bearing locknut? As stated above the only difference is the 'fixed' hub just fits onto the splined driveshaft and bolts to the wheel hub - hence the permenant drive..... the locknut is held in place with a lock washer (big ring...

Just got 60L of veggie oil in costco..... just under £15 for 15L so got 4 lots :thumb2 worked out to just under a £1 a litre :clap:clap

bit late for a reply on this but..... no special tolls required, just remove the locking ring (2 small screws) and then either a screwdriver and small hammer or I used a pair of long nosed pliers in the appropriate holes on the nut as it was not too tight.... call it a nut but it is a large...

steering gaiter or do you mean the rubber gaiter on the driveshaft?

Agree with Rick on this one.... no/very low gas = no compressor running. I redid myself with a refill can from e bay and got it working fine, right up uintil the condenser broke :doh:doh... now saving the £100 ish to replace with a new one :thumb2

Halfords sell a paint kit for most metallic colours, has paint, laquer and a little pen thing to do the edges first.... never used one but might do the trick?..... As for insurance I am 16 months into a claim where someone (in his works van) damaged my car, which was parked in a designated...

Anyone know where I can get a nearside air vent for the dash of my 2002 terrano? I gues they just prise out?? Mine have always been missing all the flappy bit inside, only a few veins left which dont do a lot :(

Thanks for that.... nto sure whether to try sticky ones again or remove the shaft...... both sides seem to have tiny drops of grease along the seam as I guess there is a pin sized gap in the glueing? Certainly found the sticky ones easy last time so might give them a go again (and be much more...

I guess this has been asked dozens of times but.... what is the easiest way to change the drive gaiter on the T2?... I have used the 'split type' boot/gaiter which you glue but they seem to leak a tiny bit along the seams? (MOT due in september so sussing out how much work I will need to do!!) I...

could the 75kg be the maximum nose weight of the van when loaded????? :nenau

mine has tons of paste around the joint from turbo outlet/exhaust pipe... was like it when I got it and will sort it out when needed..looks like mine has had a new front pipe :nenau