Search results

that's me paid up for another year . well worth paying up for all the help you can get from a good lot of friendly bunch .

thanks banshee I have left it . now just got to get use to the harder suspension now and that it does handle so good on corners .but that could be me just thinking the front is slipping

what I was trying to ask is should I adjust the front so that there is the same gap between the front and the rear . 1.5 inches on the passengers or 2 inches on the drivers side . or would there be something on the back passenger side to cause the half inch drop in differences ?.

hi all I need some advice and help . I have been trying to raise the front because they have been hitting on the rubber bound bump. so I done it like it says in section fa9 and fa39 of the workshop manual download which tells me that the vehicle posture should be 32mm . i have managed to get...

I have been told that it will fail mot if you have one on and one off?. not sure if that's true . contact cncfabs he might have some on the t2's his breaking

yes it does stop it from returning when they break up .

yes something like this _l l_ this is the best I can do it on the keyboard

I got a some spare plastic ones here which I got from Nissan dealers and a digital calliper . the sizes I am getting is 14.6mm on the outside 12.7mm inside and length is 15mm and on the length theirs a collar which is 1.5mm thick and is 3mm higher than the outside measurement

non return pedal has been on here . I think a lot of them have had the plastic bushes broke up . once replaced it has been fine

where's your grease nipple on the drivers side tie rod ?. you can see the hole but no nipple . I can't see the other ends. plus can't see a split pin in the idler arm

the tyre size is wrong surely it should be 235/70/16 not 275/30/16

no you need 8mm for feed and 6mm for return inner diameters you can get it from here on ebay . http://www.ebay.co.uk/itm/SAE-J30-R6-Unleaded-Reinforced-Rubber-Petrol-Pipe-Nitrile-Diesel-Fuel-Line-Hose-/140644526201?pt=LH_DefaultDomain_3&var=&hash=item20bf112879

I know what it is and it a waste of time getting them . it the plastic bushes that go on the spring they crack up . I have just done mine about 2 months ago . because I had the same creaking noise and now it is coming back it the part number 46512m . its not the other ones that goes on the pedal...

I could sit here typing it all out but you can look it up in the downloads it shows you there how to do it and it easier

look it up in the workshop download its in the fa section

the right way is measure from the lower link spindle bolt to the ground and the measure from the bottom of the steering stop to ground and take one off the other and the remainder should be 32mm or 1.26 inch if not adjust the torsion bar to suit . mine was 15mm

I got a kit from Halfords and the rubber bung kept splitting after about a week . I tried it with 3 of them from Halfords . so I made my own from some of the pipe and a old broke 4mm drill bit to plug it and then ground it off flush . its loads better been ok now for 6 months

I was going to get one that does both as 80% of the time I will be welding in the open and the wind will blow the gas away as I don't have anywhere under cover to work on my car

so it's not blowing threw the metal ? . what gauge metal have you been welding ? because I got some welding to do on the floor and wing of my t2 and I don't want to waste money get something with to high of a power that can't do the job or too low that it can't weld chassis when need . I went...

how can I rig a 30 amp socket . I have tried to find socket with 30 amps and can't even the cooker switch is only 13amp on the plug side