Latest project started Monday to keep me busy

Nissan 4x4 Owners Club Forum

Help Support Nissan 4x4 Owners Club Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Free meal Rick! And a couple or 3 scotch's:naughty
What a transformation. It's a shame most people will have no idea what graft went into their meal out.
 
It’s looking nice is that place, you’ll have to finish the thread with a run down of the meal :lol
 
Free meal Rick! And a couple or 3 scotch's:naughty
What a transformation. It's a shame most people will have no idea what graft went into their meal out.

Here Here

Top efforts Rick, another thread I've enjoyed keeping my eye on :thumbs
 
Ah OK I took these pics on my phone, as left camera at home and while I thought I set it to low res it was still on high and pics came in at over 4 meg, but tried loading this one and seems there is an auto resizing thingy on here, well done whoever is responsible it makes things a lot easier.

Well this is another example of the standard of plumbing by the previous people, inch and half pipe into a two inch fitting and finished with mastic but as pipe had moved was not good, also the other hole was where the boiler condensate waste discharged, with no trap
 

Attachments

  • 20171109_151421[1].jpg
    20171109_151421[1].jpg
    71.2 KB
Bar rear shelving being stocked
 

Attachments

  • 20171109_190734[1].jpg
    20171109_190734[1].jpg
    58.3 KB
OK minor grump, the pics are being rotated 90

Wine rack with some stock
 

Attachments

  • 20171109_190750[1].jpg
    20171109_190750[1].jpg
    80.1 KB
New hand basin and sink, all the boxing in will be renewed tomorrow and covered in plastic sheet, it is coming together fast now, chef complained oven not working today so last thing today at 8.30 pm found thermocouple no good so replaced it from stock I carry on the car, all for today, hope for easier day tomorrow, Rick
 

Attachments

  • 20171109_190911[1].jpg
    20171109_190911[1].jpg
    73.5 KB
OK so will try not to use phone camera any more as I now have a cricked neck as I am sure most of you have, unless Banshee can sort this issue, which I think is a very important one, to be able to upload without complicated resizing has to be worth working on, Rick
 
OK back to trusted Nikon.

New hand basin and sink with cladding, (green is protective peel off stuff)
 

Attachments

  • DSCN5101.jpg
    DSCN5101.jpg
    40.9 KB
Doors to wine rack, just needing bottom track.

So last day tomorrow, I have two rads to connect and boiler to sort, lads have lots little jobs like loo roll holders/door stops etc, lecy still has a few bits to sort, I.T guy is still busy (has probs with his cat 5/6 cables/terminations) beer people have broken bar pump bracket, but sorted the Co leaks, I left tilers with slow setting mix for front "BEARS" logo in mosaic, hope they sorted that, steam oven has been dispatched for repair as it is under warranty, still no sign of the shop sign, promised tomorrow, however we will open on Sunday, Rick
 

Attachments

  • DSCN5104.jpg
    DSCN5104.jpg
    96.2 KB
Shop front, block paving done but entrance not so, I told the tilers that if that cement based product had not cured by now then it is not going to and will need scrapping up and new applied, did they listen? ! they said they will finish it tomorrow, shop sign did not show up either
 

Attachments

  • DSCN5105.jpg
    DSCN5105.jpg
    73.5 KB
Wine rack with doors and heating all piped up and running
 

Attachments

  • DSCN5106.jpg
    DSCN5106.jpg
    107.9 KB
Raised seating area, all the staff have to do now is final clean up and sort table accessories etc
 

Attachments

  • DSCN5107.jpg
    DSCN5107.jpg
    75.8 KB

Latest posts

Back
Top