Search results

Nissan 4x4 Owners Club Forum

Help Support Nissan 4x4 Owners Club Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. 61jason61

    cobra 19 DX EU cb radio

    Make sensible offer
  2. 61jason61

    New Sig

    what the hell is a sig?
  3. 61jason61

    turbo whistle?

    iv been getting a whistle around 2.5k rpms. although had a new downpipe fitted before noticing it and clutch is/was iffy. now seems to pull hard without any slip again. wierd
  4. 61jason61

    cobra 19 DX EU cb radio

    Cobra 19 for sale. As new. £35 collection or delivery local to tidworth
  5. 61jason61

    ok its a ford ranger BUT LOOK.............

    OUR NEW LOCAL POLICE VEHICLE HERE ON SALISBURY PLAIN:clap:clap:lol
  6. 61jason61

    countryfile today, green laning piece

    not seen it yet. mentions wiltshire and cumbria, asking us to keep to legal green lanes as we all do/should. in first ten fifteen minutes. if not seen should be on iplayer soon
  7. 61jason61

    clutch change, any takers?

    a local garage offered 400 cash, scrappy do work on cars and charge 40 hour
  8. 61jason61

    Milners

    i rang them for quote on parts and got 5% when i mentioned member on here.:clap:clap
  9. 61jason61

    clutch change, any takers?

    according to garages local its a 7/7.5 hour job:eek::eek::eek::eek:
  10. 61jason61

    clutch change - flywheel question

    that dual mass thingy he mentioned that. he wanted to know if it was one. was thinking in my time on this mortal planet, if i've or me dad have had a clutch done never changed a flywheel. was getting panickey when ford said they couldn't get one. milners have two clutches listed for this...
  11. 61jason61

    Tow bar socket wiring

    also, you should nip to halfrauds and get a proper light box unit. you must by law have an audible or visual tell tale for rear turn signals. if visual tell tale must be a seperate bulb to dash turn signal tell tale lights having said that i havn't as of yet but intend to fit one, nice to know...
  12. 61jason61

    Tow bar socket wiring

    ooooh, no. not read replies but trailer wiring is my speciality no 1 is yellow right turn, two is blue fog, three is white earth, four is green left turn, fifth is brown left side, sixth is red stop, seventh middle wire is black right side light. i'm a deamon with trailer lighting, done it...
  13. 61jason61

    clutch change - flywheel question

    my garage local to me has suggested changing the flywheel at the same time as the clutch. trying to find one!! has been suggested it may not have a fly wheel?? i expect it does, where can i find one cheap? and should i need to fit it 2.7 td with 120,000 FORD CAN'T GET ME ONE!!
  14. 61jason61

    Clutch

    my clutch bites high, almost at end of clutch travel, how do you adjust? may cure my prob, may not but worth a go before ordering a new clutch :rolleyes:
  15. 61jason61

    clutch change, any takers?

    whos up for doing a clutch change , 1996 maverick td2.7 and how much lol
  16. 61jason61

    CLUTCH, similar issue to other thread

    right mot all sorted, few things need changing to improve her rear brake system but legal. now when i parked it up after original mot, three days later i went to take to town for mot work, and the clutch pedal had gone really '' light ''. i also noticed massive clutch slip over 2000 rpm in...
  17. 61jason61

    MOT, getting there

    well when i say i've done the work what i meant is my mate at meritrye in andover where my partner works, did the track rod ends and both anti roll bars both ends for £30 what a dude. i did the no plate, seat belt and wheel bearing lol, however had to replace a wheel stud merityre accidentaly...
  18. 61jason61

    MOT, getting there

    well, i have now done the following: front number plate replaced nearside rear most seatbelt had damage, both rear most belts cut out as dont require seven seats both track rod end ball joints now replaced both anti roll bars have both ball joints replaced offside wheel bearing adjusted and...
  19. 61jason61

    Who wants to do my Torsion Bars? (Dorset)

    almost suggested zippy656 lol, and hes replied. zippy in need of you.
  20. 61jason61

    wheel bearing question

    ok so i need to check and tighten the thing that looks like a revolver cylinder (with many many bullet holes) lol failing that replace bearings with the ones i have that seem good. gonna get local garage to check em over.
Back
Top