MOT = lower wishbone bush

[paulp]

Passed MOT today- well pleased.

1 advisory = lower wishbone bush

Any hints and tips please

Thanks and regards Paulp

 

[macabethiel]

MoT advisory

If it passed then there was little or no play so its probably just to cover themselves where the outer part of the rubber appears to be perished.

 

[melissachels]

I just got some new rear lower wishbone ones cos mine were gubbed for various reasons:sly I got these off ebay genuine nissan ones too tho pricey :thumb2

these are the ones the torsion bar bolt goes thru

http://www.ebay.co.uk/itm/201009026526?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649

 

[Banshee]

I just got some new rear lower wishbone ones cos mine were gubbed for various reasons:sly I got these off ebay genuine nissan ones too tho pricey :thumb2

these are the ones the torsion bar bolt goes thru

http://www.ebay.co.uk/itm/201009026526?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649

You'd have been better off with Polybushes and hey would have been a nice shiny Orange colour

 

[melissachels]

don't think you get poly bushes for that one, I did look & came up with nowt
got a full poly bush kit for everything else tho

 

[makeitfit]

poly bush N/A for that bit unless you commission a batch
However that is probably one of the worst bushes to do in poly as it'll be well hard on the road . If you want offroad improvements then more flex is good and again poly will generally restrict such movement
The bush can sometimes be fine but the comp rod can wear through the chassis

 

[melissachels]

poly bush N/A for that bit unless you commission a batch
However that is probably one of the worst bushes to do in poly as it'll be well hard on the road . If you want offroad improvements then more flex is good and again poly will generally restrict such movement
The bush can sometimes be fine but the comp rod can wear through the chassis

yes i had noticed that several supposed circle holes are now.....erm.....oval I shall be sorting that also :thumb2

 

[Banshee]

poly bush N/A for that bit unless you commission a batch
However that is probably one of the worst bushes to do in poly as it'll be well hard on the road . If you want offroad improvements then more flex is good and again poly will generally restrict such movement
The bush can sometimes be fine but the comp rod can wear through the chassis

I've got compression rod polybushes :thumb2

 

[makeitfit]

Fair play They weren't around when I searched for them a few years back. Then again I was happy not to find them when I learned how stiff they make things , oo er missus
Rose jointed mine instead, less restrictive but picks up road noise really well

 

[Kishada]

If it passed then there was little or no play so its probably just to cover themselves where the outer part of the rubber appears to be perished.

Please do not take the following as a rant at you because it is not.
It is to offer guidance about the way the system works from someone who does it first hand :doh

With regards to advisories, irrespective of the component or system, the MOT computer only allows you a preset comment unless the tester adds an additional piece of text eg borderline, so it potentially could be quite bad.

Take brake pipes for example. Unless the tester fails them for being excessively corroded then the preset text will advise them as being 'slightly' corroded unless an additional comment is added. Tester has covered his arse with selecting the advisory. Whether he cares enough to try to encourage the presenter to rectify the fault sooner rather than later, or is concerned enough by the fact the component may fail soon after the test, would include some of the few influences that would play toward adding an additional comment. I will always enter additional comments when I feel the preset text may prove misleading, but we should be entering purely factual information rather than opinion based. The opinion based decision was the initial pass or fail verdict on that component.

MOT=minimum standard, time of test, what can be seen without removing items and not necessarily giving the presenter the full picture on advisory items.

People that believe a car is 'mint' because it's just passed a test are in some respects either misguided or just ignorant of the facts.

Hope this proves informative:thumbs

P.S. Testing four wheel drives is probably not most mot testers idea of fun as they present double or triple the complexity of what is tested on a routine daily basis all still to be done within the hour slot. My personal opinion on this is that it increases the likelihood of defects being missed!

 

[Dynamics]

Hope this proves informative

Yes it has, thank you for the factual information.