Search results

what about these . http://www.ebay.co.uk/itm/Nissan-Terrano-Bull-Bar-/111386213171?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item19ef22bb33 or this one http://www.ebay.co.uk/itm/Nissan-Terrano-A-Bar-1996-Genuine-OE-/281368216520?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item4182da43c8

its not been leaking oil . it doesn't look damaged and like you said if it goes threw a oil seal then it not going to be too tight. thanks for that

should there be a little up and down and left to right movement in it . it's not the uj's it's the little bit the goes into the gearbox/transferbox

right guys on the rear prop shaft on the rear of the gearbox should there be any movement. it's not the uj's . it's coming from the bit that goes into the gearbox. when driving it sound very tinny . so I had a look and there a cup on the gearbox end and there movement between the inner and outer...

I got a light that come on the dash when I put on just the front fogs and I have another for the rear fog

I got the newer side step where they bolt into the alli not on slides

for the wood effect trim where the gear sticks are just gentle ease up till it pops up and then unscrew the gear knobs .then you should see some more screw that hold the centre wood effect bit on. as far as I can see on the manual there are 6 screws for the middle 2 behide the stereo then 2...

you are right there are 3 plates to hold the side steps on that model . I just took mine off as the alli on the middle bracket was rotten

thanks for the advice rick . they took it to a garage and they think it was the starter knackered . because they think it was the starter kept turn over and that was the noise . but I can't understand is he told me it kept going when he turned the key off and that would not happen with the...

I don't know if it kept reving the nuts off . but we went out Sunday for a drive and when was following him out it kept puffing out little clouds of blue/whitish smoke and it smelled like red hot and burning . but on the way back it was still doing the whitish clouds but every now and then it...

my father in law this morning went out to start his 2001 2.7 t2 and it made a noise when he started it . so he said he turned it off and it kept on running . so he put it in 5th and put on the brakes and let the clutch up to kill it . anyone got any idea's what could cause this ?

are you on about the wood effect trim ? . if so you pull the gater one of then you have to remove the radio and the ash tray and you should see the screws . if its the speedo one you have to remove the 3 or4 screws that holds the lower cream trim by your feet on .then remove the 5 that holds...

it could be the cable bracket on the back of the heater dials . they break . my friend set his too hot because it broke . you can fix them using computer screws

I was trying to follow this site for teaching me . http://www.mig-welding.co.uk/power-settings.htm

I have been trying to do some fillet welds to make a tee joint and its not going well . I am doing it with 2mm plate . the setting are fine when I do a butt joint on the plate doesn't blow threw and have good penetration. but as soon as I try the tee it becomes blobs and then blows threw plus I...

this is the 2nd pic

the weld picture at the top has too much juice or the man with the welder is movins slow and needs to speed up. very intrested in seing the reverse of that this is the back of the first pic

here is the 2nd pic

hi all I am trying to teaching myself to weld and need advice on my welds do they look ok and how do you weld a 90 degree angle I tried on the same setting and it just blew threw and made a mess . the pic is using a Clarke 130en set on 1/min and wire speed 6 the 2nd pic that marked 1 is 3...

yeah well worth every penny. I have had friends say why pay out for web forums. but you guys have saved me hundreds of pounds . plus even got one over on the father in law with a leaky fuel lines . he reckoned that it wouldn't cause misfire and smoke . so he paid a garage to look at it because...