Scrapping T2

[solarman216]

Got any crank position sensors that go into the front of the chest mate?

Had a look but only got Bosch ones that go in the bell housing, I have two running motors with the Zexel pump with CPS in timing case and they are both different on has one bolt the other has two, they should read 1500 ohms resistance, the Bosch ones read less than 1000, Rick

 

[t2chris]

Had a look but only got Bosch ones that go in the bell housing, I have two running motors with the Zexel pump with CPS in timing case and they are both different on has one bolt the other has two, they should read 1500 ohms resistance, the Bosch ones read less than 1000, Rick

Thanks for looking Rick, mine has the one bolt and three pin connector, I imagine since i have hitachi maf then I dont have bosch cps?!

What would you want for that one mate?

Chris

 

[solarman216]

Rusty nuts,,, what Mk I have one for the Mk 1 not for Mk2

Smiler,,, no commercials.

R1cho,,,,no boot light used the last one on Mrs motor as it fell to bits changing the bulb

Clivvy ,,, nearest I have is an early Mk 1 looks similar in colour, it is the LPG one that I would like to sell as seems a shame to break it with MOT till July next year, Rick

 

[solarman216]

Thanks for looking Rick, mine has the one bolt and three pin connector, I imagine since i have hitachi maf then I dont have bosch cps?!

What would you want for that one mate?

Chris

The Bosch one is no good to you as although it has one bolt and may fit the hole (I do not know) the coil resistance is around 800 ohms, far too low against your 1500, Rick

 

[R1cho]

R1cho,,,,no boot light used the last one on Mrs motor as it fell to bits changing the bulb

thats what happened to mine :lol:lol

 

[melissachels]

Is it td's or Tdi's you scraping Rick?

Phil's got some tdi wiring for me, but struggling to get wireing looms for td. Would be looking for the wiring loom that attachs to the ecu & the fuel pump ones.

Cheers,
Mel

 

[Mark charlesworth]

Bosch maf sensor if you got one, and an auto gearbox please

 

[panelbeater]

any matching 15" t2 alloys

 

[solarman216]

Is it td's or Tdi's you scraping Rick?

Phil's got some tdi wiring for me, but struggling to get wireing looms for td. Would be looking for the wiring loom that attachs to the ecu & the fuel pump ones.

Cheers,
Mel

The Diesel one is a TDi if you want the loom it is still all there, Rick

 

[solarman216]

Bosch maf sensor if you got one, and an auto gearbox please

Bosch Maf has gone, and only manual boxes sorry, Rick

 

[solarman216]

any matching 15" t2 alloys

Got quite a few alloys, will have to look in the daylight tomorrow as have many different styles, to see if I have 4 the same, Rick

 

[solarman216]

Am sure I have a set of 5 Ford alloys, Rick

 

[melissachels]

The Diesel one is a TDi if you want the loom it is still all there, Rick

cheers, but its really a set of TD ones I need :thumbs

 

[JCH]

Running boards

Any running boards available for T2. 2003

 

[panelbeater]

any chance of photo of wheels rick please and condition.

 

[solarman216]

cheers, but its really a set of TD ones I need :thumbs

Ah sorry misread your post, Rick

 

[solarman216]

Any running boards available for T2. 2003

I have two sets of side steps, but ship to France? Rick

 

[solarman216]

any chance of photo of wheels rick please and condition.

I have 5 of these in good condition, the marks in the pic are only algae, they just need a clean, Rick

 

[solarman216]

And I have 4 of these, again only need a clean, Rick

 

[Mark charlesworth]

Rick do you have the front grill not worried about colour, silver or blue 1st choice but as I said not worried about colour. Cheers