Paper clip

[Mark charlesworth]

Help I read yesterday how to use a paper clip to sort out eml can some one point me in the right direction thanks in advanced

 

[clivvy]

http://www.nissan4x4ownersclub.com/links.htm

eighth link down I think:thumbs

 

[Mark charlesworth]

That's the kiddie thank you clivvy

 

[Mark charlesworth]

Looks like its a no:18
Fuel quality adjuster/position sensor-malfunction. Might as well ask me to speak Russian I have not got a clue can any one help please

 

[jonela]

Looks like its a no:18
Fuel quality adjuster/position sensor-malfunction. Might as well ask me to speak Russian I have not got a clue can any one help please

Your men for this are solaman (Rick) or davenclair. If you want to understand more about readings and fault codes it's best to get yourself a consult interface;
http://www.ebay.co.uk/itm/Nissan-Co...iagnostic_Tools_Equipment&hash=item3f30a4a199 and download ECUTalke
http://www.ecutalk.com/ecutalk.aspx
also look it this tread
http://www.nissan4x4ownersclub.com/forum/showthread.php?t=21534

 

[Mark charlesworth]

Just ordered ecutalk so I can have a play around

 

[Banshee]

Just ordered ecutalk so I can have a play around

Ordered?!?! Dude it's free!!!

Is yours a 14 pin or 16 pin?

 

[Mark charlesworth]

It's the 14 pin

 

[Banshee]

It's the 14 pin

No messing around then mate consult cable straight into the laptop with a USB to serial cable and you're away

 

[clivvy]

I had No18 too, was never anything to do with the pump so don't rush out to replace it yet!

 

[Mark charlesworth]

Being an auto ticks over at about 800rpm put it in to gear rpm drops as it should but if I turn the stering wheel so the power stering pump has to work some times the engine cuts out, and when I re start the eml comes on but still drives ok, no power loss or any thing

 

[rayf3262]

Being an auto ticks over at about 800rpm put it in to gear rpm drops as it should but if I turn the stering wheel so the power stering pump has to work some times the engine cuts out, and when I re start the eml comes on but still drives ok, no power loss or any thing

Does your truck have air con.?

 

[Mark charlesworth]

It has air con but not very cold

 

[rayf3262]

Check that when the air con is switched on the engine idle speed increases by 100 RPM.

With the air off, when driving and coming to a stop, after around 1~2 seconds stationary the idle speed should drop by 100 rpm to normal idle speed.

 

[solarman216]

there is also a pressure switch on the PS that should increase revs when PS is under load, could be this has failed, Rick

 

[Mark charlesworth]

Thanks for the info Rick will look tomorrow

 

[spautoparts]

I have the exact same problem with mine. Mine also is the automatic gearbox. When I put it into gear it sometimes stalls the engine and I get code 18. I switch off the engine and back on and it clears it. Ive been putting up with it for almost a year but really want to get it sorted.

 

[davenclaire]

im happy to plug you into my laptop to check and clear your codes.
iv also resealed our injector pump while still on the car so iv become dare i say it bit of an expert on the ip. happy to help out where abouts are you?

 

[Mark charlesworth]

I'm in Eltham just off the a2

 

[davenclaire]

well blow me down im in orpington next door. for what its worth i think your control sleeve position sensor housing needs a little adjustement you cant turn the tick over up but slight adjustments to the housing have the same effect. you may also have a leaking pump usually the seals go hard n brittle look up my post on resealing the pump it shows you where to look