Heater Blower Resistor

[Timbo_1975]

Ok peoples, I need a new one for a customers car. Who sells em?

Quick look on milner and my local parts shop which has yielded nowt.

 

[lacroupade]

Ok peoples, I need a new one for a customers car. Who sells em?

Quick look on milner and my local parts shop which has yielded nowt.

Maplins?

 

[solarman216]

it will be Nissan I think, what model is it I have a Mk 1 resistor but you may not want a used one for a customer, I purchased a Mk 2 from Nissan and it was not too bad I thought at around £30 it is the printed circuit type whereas the Mk 1 is coiled wire, Rick

 

[Timbo_1975]

Its for a 04 T2 Tdi. Dealer only, typical!!

 

[wildbri]

see the workshop downloads, when mine went faulty I was able to solder repair the circuit board break. Cost nil and that was three years ago. regards bri

 

[zippy656]

see the workshop downloads, when mine went faulty I was able to solder repair the circuit board break. Cost nil and that was three years ago. regards bri

i was going to say that...


oh well

 

[glen]

hi this is what i did

Heater Control card that controls speed
control card can be found in the heater motor, firstly remove the wiring plug-in connecter, there are two cross headed self tappers holding the connecter block in the moter body take these out and out comes the control card, use a very short screwdriver

It is a small circuit board which is locaed in a very hard to get at place underneath and behind the glove compartment. about 30 minutes of fiddling around. The part was about £35

Glen

 

[Thomas-the-Terrano2]

well my new 02 t2 mk4 has this fault

no fan unless on a 4.

quick glance cant see anywhere into dash,

any clues, and is it a part or whole assembly
i'll need.

is it possible to use another dial?



never had this on the old t2 mk2

 

[4wheel]

To be found under the glove compartment.Fiddly to remove.Repaired mine with a dash of solder but available from Nissan only for about £25.

 

[Thomas-the-Terrano2]

sorry is resistor under glove box,
or are you saying remove glove box
to access switch.

also want to get in there to hard wire
the cb, that is when i decide if its going
up on top of dash or in cubby hole
behind gear sticks...

 

[Fez_uk]

No look from below the dash in the passenger side. It's a resistor thing your looking for, you will only see the connector. You need to unscrew it.

http://www.ebay.co.uk/itm/NISSAN-AL...CarParts_SM&hash=item4aadd40b72#ht_500wt_1156

Looks like that but you only see the connection side. You can find the same on all sorts of nissan cars. I got mine from a scrapyard for £2 from a primera I think

I'd personally get another 2nd hand one, the bit of solder method may work but why did it blow in the first place? It's there for a reason.

 

[wildbri]

http://www.nissan4x4ownersclub.com/downloads/workshop/wk18.pdf and here you will find the down load and how to fix it... regards bri

 

[wildbri]

I dont think it "blows" I think that it just melts the flimsy printed circuit, my repair is in its fourth year, bri

 

[Thomas-the-Terrano2]

cheers bri and franz, forgot about the workshops,

so not even in the dash - has assumed was behind
the dial, that make its atleast a bit easier, hopefully

 

[Kamsin]

I have fixed mine today and will make an entry on the down loads section for you to see how to fix it...

 

[Timbo_1975]

Marvellous!!!