Search results

This was an option that i was told about at a motor factors, but to be honest I wasn't sure I was capable of it all,as I have never fitted anything like that before.

The soldering was hard going due to the temp as I only have a basic iron, but the twists were as tight as I could get them & seemed strong. The lamp does work but only very low light & flickers, from time to time it wont come on at all.Every now & again I do get full power from it though too.

Hi, Thanks for the reply first of all. Yep your right about where I took the feed from & thats why I shrink sealed them & used self adhesive shrink too to help ensure the best seal. I did test the lamp & it's working perfectly, in fact I surprised myself at just how bright & crisp the light...

Evening folks, I have a little issue with my lights thats got me in a pickle! I have a 27W LED worklight that I have hooked up to the standard reversing light cable behind the light cluster. The original is just not good enough anymore,so an upgrade was in order. The trouble is that after...

Well I renewed again recently as this is one of the best forums/websites going. The amount of help & advice on here is simply superb. To top it all,everybody is really friendly,which makes asking questions a lot easier as a bloke, as we tend to pretend we can do it all already :D Thanks again...

Hello again! Sorry for not posting back here sooner but I had to go off on a job & I simply forgot about this until the issue started again.:doh The reversing light has stopped now totally. I had the gearbox switch swapped for a new one & nothing changed. So I have got myself a multi-meter to...

Yeah, still no joy sadly, but thanks anyway. Unless I've missed something:doh

Hi, Quick question. I've searched the forums but cant find the right answer. My reversing light has stopped working, so I swapped the bulb & it's still no go. I cant find any reference to a fuse that covers that light, does anybody know which it could be? I was searching on Google & found...

My first information was that the compressor was OK. It was tested I'm told & was running OK but they thought it was an electrical fault as it seemed no power was getting through to it. Confused.com

Thanks for the replies so far folks. Got my hands on the print out from the garage! It reads as follows: Attempt to carry out an air conditioning service - Gas still present within system on car. Suspect electrical fault causing compressor to not engage. Checked all fuses & relays - all ok...

Hi all, I have an odd one here, my air con stopped blowing cold last week & started blowing anything between coolish to outside temp/warm. The compressor seemed to be going OK, so i assumed it needed a re-gas etc. Booked it in & she was looked over today, the garage said gas was...

Hi, I'm having trouble getting the panel off, I can't get these clips to release at all. Just to clarify, I push the centre down & they release? Should I hear or feel any click when they release? Also,is it best to just use your finger or use a tool? Thanks! Sent from my iPhone

Update: I had done the job,but at the very end the seal didn't fit, despite it being the correct part number & over laying the two seals etc to check sizes. Nissan claim a faulty part, so I'm off to swap it. Sent from my iPhone

Superb answer! Thank you very much for your help tonight I will take time to check out the pin to see if it is tapered etc thanks for that, it's a very good idea too about keeping hold of the T shaped pins as back up. I have the door sealed with tape tonight in case it rains again, as it...

Thanks for the answers guys. Sweety,yeah it's a one piece seal & is complete with the little fixings too. I just didn't want to start messing with any door fixings without first checking with others who had already done it. So when I tap out the roll pin,does it matter if that is tapped from...

Any advice on the above would be great, I'm desperate to get the new seal in place before we get anymore heavy rain. Thanks! Sent from my iPhone

I have just bought a new weather seal (£120 inc VAT,bloody rip off a new AT tyre was only £10 more!!!) for the boot door & it needs fitting ASAP & I also bought & fitted a brand new weather strip (£68 + VAT), you know the bit that fits to the lip along the roof line that the door seal kisses...

Yeah it's a pain in the arse in the dark! I will get around to this one soon & maybe take some pics too if I remember. Thanks for your reply.:thumbs

Image two.

I have to remove the scuttle panel, how did you do this? The fiitings dont seem to have any form of 'fitting' in them for a tool to fit into? The rubber seal at the bottom of the screen has popped out & needs tucking in again.