Heater/AC control panel

billybuilder · 20-02-2020, 17:44

Hi still loving my 'new' 2002 Trail my latest fishing vehicle. All minor glitches sorted bar one !! one back light on the heater control illumination not working. Have swapped the two bulbs over and it is not a blown bulb. Any ideas anyone ??

solarman216 · 20-02-2020, 20:14

No first hand info on these but I would think a broken PCB track, look at the tracks that go to the bulb in question with a magnifying glass, check soldered joints as well, look for a ring around the middle of the solder, Rick

billybuilder · 20-02-2020, 21:18

Thanks Rick sounds very technical but I will have a look

solarman216 · 20-02-2020, 21:59

Picture of he PCB would be good, Rick

billybuilder · 21-02-2020, 13:14

Thanks Rick I will see what I can do

billybuilder · 05-03-2020, 22:24

Had a look Rick but can see nothing obvious at all except that where the bulb turns in to place and the wires on it make contact with the solder lines on the PCB the surface is quite badly scratched. Could not get a decent enough photo that showed this unfortunately.

Les

solarman216 · 05-03-2020, 23:34

The Mrs has a 2002 3Lt and light on clock etc seems one sided, so soon as I have time will be removing cluster to have a look, Rick

billybuilder · 07-03-2020, 20:07

Cheers Rick

20-02-2020, 17:44	#1
billybuilder Junior Member Join Date: Feb 2020 Location: Dorset Vehicle: 2002 2.0 SE+ Posts: 9	Heater/AC control panel Hi still loving my 'new' 2002 Trail my latest fishing vehicle. All minor glitches sorted bar one !! one back light on the heater control illumination not working. Have swapped the two bulbs over and it is not a blown bulb. Any ideas anyone ??

20-02-2020, 20:14	#2
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,431	No first hand info on these but I would think a broken PCB track, look at the tracks that go to the bulb in question with a magnifying glass, check soldered joints as well, look for a ring around the middle of the solder, Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

20-02-2020, 21:59	#4
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,431	Picture of he PCB would be good, Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

05-03-2020, 23:34	#7
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,431	The Mrs has a 2002 3Lt and light on clock etc seems one sided, so soon as I have time will be removing cluster to have a look, Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

20-02-2020, 21:18	#3
billybuilder Junior Member Join Date: Feb 2020 Location: Dorset Vehicle: 2002 2.0 SE+ Posts: 9	Thanks Rick sounds very technical but I will have a look

21-02-2020, 13:14	#5
billybuilder Junior Member Join Date: Feb 2020 Location: Dorset Vehicle: 2002 2.0 SE+ Posts: 9	Thanks Rick I will see what I can do

05-03-2020, 22:24	#6
billybuilder Junior Member Join Date: Feb 2020 Location: Dorset Vehicle: 2002 2.0 SE+ Posts: 9	Had a look Rick but can see nothing obvious at all except that where the bulb turns in to place and the wires on it make contact with the solder lines on the PCB the surface is quite badly scratched. Could not get a decent enough photo that showed this unfortunately. Les

07-03-2020, 20:07	#8
billybuilder Junior Member Join Date: Feb 2020 Location: Dorset Vehicle: 2002 2.0 SE+ Posts: 9	Cheers Rick