MOT Day

Banshee · 18-07-2013, 10:20

So the dreaded day has arrived

I'm pooing my pants, really don't want to have to throw any more money at Marvin the Maverick as he's been spoiled enough these past few months!!!!!

Anti Roll Bar Polybushes
New Droplinks and Polybushes
Compression Rod Polybushes
New Tie Rod Ends
New Discs and Pads
2 Newish front Tyres
New Water Pump
New Starter Motor
New Thermostat
746 Fuel Filters

He's been Waxoyled as best as I could given the time I had left, I've just been so busy with work and other stuff!!!! I was still underneath it this morning at 2am, yes yes my neighbors love me

Here's a picture of how he stands at the moment

I've also removed the bullbar as 2 brackets have now snapped on it and I don't fancy my chances on the motorway should it fall off, it's bloody rotten anyway, I've been scammed with that one!!!! I think I'm just going to mount 3-4 hella Comet 500's on the front bumper between the headlights, similar to what revolvor has done

WISH ME LUCK

trophymick · 18-07-2013, 10:45

Good luck!

96terrano · 18-07-2013, 10:47

Yes, I'm doing the same as revolver too when I get my winch bumper

Banshee · 18-07-2013, 10:55

Quote:

Originally Posted by 96terrano

Yes, I'm doing the same as revolver too when I get my winch bumper

Yeah that's def on my next list of things to do should it pass with no issues
I didn't much like the bull bar anyway as it really limited my ground clearance, I've managed to wedge myself before now because of it and had to be pulled off by a mate lol

Where you getting your bumper from?

96terrano · 18-07-2013, 11:12

Quote:

Originally Posted by Banshee

Yeah that's def on my next list of things to do should it pass with no issues
I didn't much like the bull bar anyway as it really limited my ground clearance, I've managed to wedge myself before now because of it and had to be pulled off by a mate lol

Where you getting your bumper from?

yeah, my bulbar has been hit plenty of times

the bumper is either getting mate by Pete 'makeitfit' or a guy on facebook

if youre on facebook i'll send you his details

Banshee · 18-07-2013, 11:24

Quote:

Originally Posted by 96terrano

yeah, my bulbar has been hit plenty of times

the bumper is either getting mate by Pete 'makeitfit' or a guy on facebook

if youre on facebook i'll send you his details

What kind of prices are they going for?

96terrano · 18-07-2013, 11:59

Quote:

Originally Posted by Banshee

What kind of prices are they going for?

under £200, something like £175 i think from Pete, not sure what the other guy wanted, he wouldn't say

Banshee · 18-07-2013, 12:01

Quote:

Originally Posted by 96terrano

under £200, something like £175 i think from Pete, not sure what the other guy wanted, he wouldn't say

Do they use all of the existing mounting points or do they need to be welded on etc?

Fez_uk · 18-07-2013, 12:05

it uses existing bumper mount. me and makeitfit never had any problems with the strength of the existing mount.

firebobby · 18-07-2013, 18:01

WELL, did it pass ???

Banshee · 19-07-2013, 09:44

Here's one for you

It didn't pass and it didn't fail, what happened?

makeitfit · 19-07-2013, 09:46

Catastrophic failure of a major component , like door not opening, resulting in a void test

OR did something fall on the examiners head

Banshee · 19-07-2013, 09:56

Quote:

Originally Posted by makeitfit

Catastrophic failure of a major component , like door not opening, resulting in a void test

OR did something fall on the examiners head

Wrong on both counts lol

I've taken it in to the garage at work that do all the maintenance on our fleet vehicles and one of the MD's had rocked up with his VW Golf with the ABS light flashing so intimidately mine was pushed to the back of the queue, there was only one guy in and he was taken up all day with this job so they are testing it today instead

Feel sorry for the MD who owns the Golf though!!! Apparently it needed a new ABS pump which was a dealer part and set him back £598

Banshee · 19-07-2013, 15:36

It's Failed

x1 Small patch of rust that needs welding up by drivers side front body mount

x1 Drivers Side leaking brake pipe where it attaches to caliper (I think I'm just going to need a new copper washer

x5 Pins missing in the castle nuts on the drivers side lower drop link and both inner and outer tie rod ends on both sides

woopsie

Apart from that just an advisory for a small Oil leak on the sump supposedly

And an Advisory for using too much Waxoyl

Now to get back from Nottingham and collect it and get the work done

Anyone handy with a welder who fancies an earner tonight? I don;'t mind travelling

R1cho · 19-07-2013, 16:05

Shame all my welding gear is up at new house or would have done it for you

18-07-2013, 10:20	#1
Banshee Moderator Join Date: Jul 2012 Location: West Midlands Vehicle: 04 2.7 SWB Terrano II Van Posts: 13,526	MOT Day So the dreaded day has arrived I'm pooing my pants, really don't want to have to throw any more money at Marvin the Maverick as he's been spoiled enough these past few months!!!!! Anti Roll Bar Polybushes New Droplinks and Polybushes Compression Rod Polybushes New Tie Rod Ends New Discs and Pads 2 Newish front Tyres New Water Pump New Starter Motor New Thermostat 746 Fuel Filters He's been Waxoyled as best as I could given the time I had left, I've just been so busy with work and other stuff!!!! I was still underneath it this morning at 2am, yes yes my neighbors love me Here's a picture of how he stands at the moment I've also removed the bullbar as 2 brackets have now snapped on it and I don't fancy my chances on the motorway should it fall off, it's bloody rotten anyway, I've been scammed with that one!!!! I think I'm just going to mount 3-4 hella Comet 500's on the front bumper between the headlights, similar to what revolvor has done WISH ME LUCK __________________ Moderator 04' Terrano II SE 2.7 TDi SWB Commercial in Silver - Project Thread Toyo Open Country M/T 33's on 10J Steels, Super Strong Steering Job Navara D22 Snorkel, Front LOKKA, Maunal Hubs, EGR Blank TunitII ECU Chip, 3" Body Lift, 2" Suss Lift, Heat Exchanger Black Interior, 3.0 Borg&Beck Clutch, Eckes Heated Fuel Filter 99' Y61 Patrol GR SE 2.8 TD6 LWB in Blue/Silver - Project Thread Engine Transplant - In Progress!!! Last edited by Banshee; 19-07-2017 at 11:29.

19-07-2013, 09:44	#11
Banshee Moderator Join Date: Jul 2012 Location: West Midlands Vehicle: 04 2.7 SWB Terrano II Van Posts: 13,526	Here's one for you It didn't pass and it didn't fail, what happened? __________________ Moderator 04' Terrano II SE 2.7 TDi SWB Commercial in Silver - Project Thread Toyo Open Country M/T 33's on 10J Steels, Super Strong Steering Job Navara D22 Snorkel, Front LOKKA, Maunal Hubs, EGR Blank TunitII ECU Chip, 3" Body Lift, 2" Suss Lift, Heat Exchanger Black Interior, 3.0 Borg&Beck Clutch, Eckes Heated Fuel Filter 99' Y61 Patrol GR SE 2.8 TD6 LWB in Blue/Silver - Project Thread Engine Transplant - In Progress!!!

19-07-2013, 15:36	#14
Banshee Moderator Join Date: Jul 2012 Location: West Midlands Vehicle: 04 2.7 SWB Terrano II Van Posts: 13,526	It's Failed x1 Small patch of rust that needs welding up by drivers side front body mount x1 Drivers Side leaking brake pipe where it attaches to caliper (I think I'm just going to need a new copper washer x5 Pins missing in the castle nuts on the drivers side lower drop link and both inner and outer tie rod ends on both sides woopsie Apart from that just an advisory for a small Oil leak on the sump supposedly And an Advisory for using too much Waxoyl Now to get back from Nottingham and collect it and get the work done Anyone handy with a welder who fancies an earner tonight? I don;'t mind travelling __________________ Moderator 04' Terrano II SE 2.7 TDi SWB Commercial in Silver - Project Thread Toyo Open Country M/T 33's on 10J Steels, Super Strong Steering Job Navara D22 Snorkel, Front LOKKA, Maunal Hubs, EGR Blank TunitII ECU Chip, 3" Body Lift, 2" Suss Lift, Heat Exchanger Black Interior, 3.0 Borg&Beck Clutch, Eckes Heated Fuel Filter 99' Y61 Patrol GR SE 2.8 TD6 LWB in Blue/Silver - Project Thread Engine Transplant - In Progress!!!

18-07-2013, 10:45	#2
trophymick Senior Member Join Date: Feb 2013 Location: Langholm,Scotland Vehicle: 2001 Terrano 2. S LWB 2.7 Posts: 463	Good luck!

18-07-2013, 10:47	#3
96terrano Senior Member Join Date: Jun 2010 Location: Dumfries and Galloway, Scotland Vehicle: Nissan Terrano 2.7TD LWB Posts: 8,024	Yes, I'm doing the same as revolver too when I get my winch bumper

18-07-2013, 12:05	#9
Fez_uk Senior Member Join Date: Sep 2010 Location: Mid-Wales Vehicle: Maverick 2.7 - Patrol 4.2 Posts: 5,645	it uses existing bumper mount. me and makeitfit never had any problems with the strength of the existing mount.

18-07-2013, 18:01	#10
firebobby Senior Member Join Date: Feb 2012 Location: South Bucks Vehicle: Terrano 3.0 SVE 2005 Posts: 3,499	WELL, did it pass ???

19-07-2013, 09:46	#12
makeitfit Senior Member Join Date: Apr 2008 Location: on the beach WEST WALES Vehicle: Maverick TDi BLACK mmm Posts: 15,136	Catastrophic failure of a major component , like door not opening, resulting in a void test OR did something fall on the examiners head

19-07-2013, 16:05	#15
R1cho Senior Member Join Date: Aug 2010 Location: Wales Vehicle: 1997 LandCruiser Colorado Posts: 4,201	Shame all my welding gear is up at new house or would have done it for you