Go Back   :::.Nissan 4x4 Owners Club.::: > General > Members free classifieds and wanted items.

Members free classifieds and wanted items. Place your Nissan/Ford 4x4 vehicles or related items for sale and wanted here.

Reply
 
Thread Tools Display Modes
Old 02-09-2012, 11:22   #1
clivvy
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Mar 2009
Location: Huddersfield
Vehicle: Terrano 03 LWB
Posts: 6,947
Default wanted - EGR blanking plate

chaps!

I really want to get my EGR done, but i need a blanking plate to slide in between the egr and manifold, anybody got one they can sell me?

cant find any on fleabay...!!
clivvy is offline   Reply With Quote
Old 02-09-2012, 12:50   #2
stinka
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Feb 2012
Location: Staffs
Vehicle: '02 Terrano TDI sport lwb
Posts: 3,787
Default

Make one

Or take off your egr valve and take it to a local engineer shop and tell them to knock up 2 4mm plates for you, thats what i did last week, cost me a tenner

I bolted them in place with 700 degree copper rtv and did away with the egr valve altogether
stinka is offline   Reply With Quote
Old 02-09-2012, 13:04   #3
clivvy
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Mar 2009
Location: Huddersfield
Vehicle: Terrano 03 LWB
Posts: 6,947
Default

fair point!

how difficult is it to actually remove the egr? The guide in Downloads doesnt show this, and i'd really like to actually remove it for cleaning...
clivvy is offline   Reply With Quote
Old 02-09-2012, 13:10   #4
stinka
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Feb 2012
Location: Staffs
Vehicle: '02 Terrano TDI sport lwb
Posts: 3,787
Default

Quote:
Originally Posted by clivvy View Post
fair point!

how difficult is it to actually remove the egr? The guide in Downloads doesnt show this, and i'd really like to actually remove it for cleaning...
its a right twat to get off. Dont bother cleaning it, waste of time. If you are removing it then plate the holes back up, dont put it back on
stinka is offline   Reply With Quote
Old 02-09-2012, 14:00   #5
clivvy
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Mar 2009
Location: Huddersfield
Vehicle: Terrano 03 LWB
Posts: 6,947
Default

ahh hbugger, I was hoping it would be relatively easy to remove.

im starting to think about selling up.
clivvy is offline   Reply With Quote
Old 02-09-2012, 14:34   #6
cncfabs
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Sep 2009
Location: somerset
Vehicle: terrano
Posts: 1,947
Default

Quote:
Originally Posted by stinka View Post
Make one

Or take off your egr valve and take it to a local engineer shop and tell them to knock up 2 4mm plates for you, thats what i did last week, cost me a tenner

I bolted them in place with 700 degree copper rtv and did away with the egr valve altogether
What material is best to use ali or steel if there worth £10 a set ill get some lasered out.
cncfabs is offline   Reply With Quote
Old 02-09-2012, 14:45   #7
clivvy
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Mar 2009
Location: Huddersfield
Vehicle: Terrano 03 LWB
Posts: 6,947
Default

let me know, because sliding in a blanking plate both ends of the egr is better than struggling to take it out...
clivvy is offline   Reply With Quote
Old 02-09-2012, 15:01   #8
mjpetersen
Member
Click here to find out how to become a paid up member
 
Join Date: Feb 2012
Location: Poland
Vehicle: Maverick 1997 lwb 2.7 tdi
Posts: 39
Default

I did not find it as difficult to remove the EGR entirely, at least as much as I was anticipating it to be based on all the comments on the forum. I do have a very nice set of ratcheting end wrenches, which helped inmensely.

I used a piece of 4 mm stainless plate that I happen to have. I traced the pattern onto the plate from the EGR valve and in only a couple of minutes of work with angle grinder and a 1mm metal cutting disk I had a couple of plates. I sanded the edges and just epoxied the one plate on the intake manifold side. The other side from the exhaust manifold needs to be bolted on--with just epoxy it lasted over 500 miles but it was scary when it came loose. The next one I made, I bolted on. It is not a hard job to do at all.

Mike
mjpetersen is offline   Reply With Quote
Old 02-09-2012, 15:05   #9
stinka
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Feb 2012
Location: Staffs
Vehicle: '02 Terrano TDI sport lwb
Posts: 3,787
Default

Quote:
Originally Posted by clivvy View Post
let me know, because sliding in a blanking plate both ends of the egr is better than struggling to take it out...
I slid one in at first but you need to get some copper rtv on it as well to ensure its gas tight, this is why you're best to remove it and blank it with 4mm plate, otherwise you'll rub all the paste off when u slide it in
stinka is offline   Reply With Quote
Old 02-09-2012, 15:09   #10
stinka
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Feb 2012
Location: Staffs
Vehicle: '02 Terrano TDI sport lwb
Posts: 3,787
Default

Quote:
Originally Posted by cncfabs View Post
What material is best to use ali or steel if there worth £10 a set ill get some lasered out.
4mm steel
stinka is offline   Reply With Quote
Old 02-09-2012, 16:49   #11
Big and Daft
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Oct 2010
Location: Manchester
Posts: 133
Default

Kamsin did a 'how to' video a while back that he uploaded to YouTube.

Here it is:
http://www.youtube.com/watch?v=GEPJxLE5GYY
Big and Daft is offline   Reply With Quote
Old 02-09-2012, 19:06   #12
clivvy
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Mar 2009
Location: Huddersfield
Vehicle: Terrano 03 LWB
Posts: 6,947
Default

thanks for the replies guys. I have seen Kamsins video, and I was worried that the EGR removal really WAS as difficult as he said it was!! ah well, Ill just have to get in there and do it, thats next weekends job.
clivvy is offline   Reply With Quote
Old 02-09-2012, 19:36   #13
stinka
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Feb 2012
Location: Staffs
Vehicle: '02 Terrano TDI sport lwb
Posts: 3,787
Default

I got the bottom bolts from the top side, i just reached under the inlet manifold with a 12mm deep socket and a ratchet, was a pain in the arse tho lol
stinka is offline   Reply With Quote
Old 02-09-2012, 19:39   #14
clivvy
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Mar 2009
Location: Huddersfield
Vehicle: Terrano 03 LWB
Posts: 6,947
Default

do you mean the two I can see, drivers side, on the side of the inlet manifold, or are there some underneath that I cant see?

hard to tell in Kamsins video
clivvy is offline   Reply With Quote
Old 02-09-2012, 19:48   #15
stinka
Senior Member
Click here to find out how to become a paid up member
 
Join Date: Feb 2012
Location: Staffs
Vehicle: '02 Terrano TDI sport lwb
Posts: 3,787
Default

Quote:
Originally Posted by clivvy View Post
do you mean the two I can see, drivers side, on the side of the inlet manifold, or are there some underneath that I cant see?

hard to tell in Kamsins video
no those are the easy ones, there are some underneath connected to a flange/pipe that runs to the exhaust manifold
stinka is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT +1. The time now is 20:11.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Images online photo albums