Dump valve on a terrano ?

[96terrano]

I seen a 3ltr t2 the other day in a carpark. "yes I did put a poster on it advertising our club" anyhoo, I heard it start up and drive off and it sounded like it had a dump valve on the turbo sounded really awesome tbh can I get one and fit it to my td27:nenau

 

[(RIP) PLANK]

don't think it would work on a diesel

 

[clivvy]

mine does that, i thought it was the waste gate or something?hammer the accelerator, quick off to change gear and PFFT....

 

[Kamsin]

Just take the exhaust pipe off at the middle and it will sound the same.

 

[makeitfit]

You can fit a dump valve to a diesel but no point. So as Kamsin said just cut your pipe or make a proper turbo down pipe with separate waste gate and exhaust pipes :sly That'll sound sweet

 

[96terrano]

You can fit a dump valve to a diesel but no point. So as Kamsin said just cut your pipe or make a proper turbo down pipe with separate waste gate and exhaust pipes :sly That'll sound sweet

How do I do that then:augie I want my terrano to sound sweet:thumb2

 

[96terrano]

Just take the exhaust pipe off at the middle and it will sound the same.

Would that not fail a MOT?

 

[makeitfit]

Would that not fail a MOT?

Take it off AFTER the mot but yes it's a fail as the gases have to clear the car at the back or the side .
Have you got a spare turbo? If so have a look at the arse end of it. There's two holes on the turbime housing, one is the waste gate the other obviously the exhaust turbine. So you take one small pipe off the turbo waste gate out somewhere and the other as normal exhaust.
Look up nissan skyline etc turbo downpipes or get a flange like this http://www.ebay.co.uk/itm/Garrett-T...arts_Vehicles_CarParts_SM&hash=item336ecb64f3

 

[96terrano]

Cheers, aye, I've got a turbo that I'll look at I'm wanting to get as much POWER!!!!! out the engine as possible:sly

 

[makeitfit]

Well you want no resistance or back pressure on the back of the turbo. Go as big as poss to get the wind out :thumb2 2 1/2" should do it, 3" is a pain to get past the bulkhead :doh

 

[geoffdown]

Take it off AFTER the mot but yes it's a fail as the gases have to clear the car at the back or the side .
Have you got a spare turbo? If so have a look at the arse end of it. There's two holes on the turbime housing, one is the waste gate the other obviously the exhaust turbine. So you take one small pipe off the turbo waste gate out somewhere and the other as normal exhaust.
Look up nissan skyline etc turbo downpipes or get a flange like this http://www.ebay.co.uk/itm/Garrett-T...arts_Vehicles_CarParts_SM&hash=item336ecb64f3

so is that the flange i need to make the downpipe from so it will be the same as ur mod down pipe in other words will it fit stright on to my rear of a standard terrano turbo im getting a new mig welder which will do tig as well so i can learn how to weld but as a back up i have my dad who can use mig,tig,arc and gas and can weld any type of metal been doing it for over 40 years:bow:naughty

 

[stinka]

fit a snorkel like mine, which is basically 3" open pipe from the turbo inlet, sounds sweet as fk tbh

 

[makeitfit]

Nearly but not quite I wish I could find the right flange off the shelf . The turbo is a Garratt T25 but it seems a tad modified for Nissan I think.
I've ordered one and it doesn't quite fit :doh
So it's probably make one

 

[geoffdown]

Nearly but not quite I wish I could find the right flange off the shelf . The turbo is a Garratt T25 but it seems a tad modified for Nissan I think.
I've ordered one and it doesn't quite fit :doh
So it's probably make one

Would ur welder surply just the flange and if so how much

 

[makeitfit]

He can get laser cut ones made no worries. The last time I asked him , he said the company that makes them have a minimum order value. He's got a few other jobs coming up soon, so we could be in the 25 pound mark.

 

[96terrano]

Are garrett a good manufacturer?

 

[makeitfit]

Hope so

 

[96terrano]

Time for a bit of early morning research, then bed:lol:lol

 

[96terrano]

Interesting, garrett is bassicly a sub name from the main manufacturer "honeywell" so it's bassicly a honeywell turbo that terranos have . Well, that's what it sounds like

Seem good products:thumbs


http://www.honeywell.com/sites/uk/t...2AD_H6D29E681-A2CB-08B4-CF02-CB888231D808.htm

 

[Kamsin]

He can get laser cut ones made no worries. The last time I asked him , he said the company that makes them have a minimum order value. He's got a few other jobs coming up soon, so we could be in the 25 pound mark.

I dont know what it is yet, but if we talking more pawer then i want one as well! :thumbs