Search results

I have asked about speedo stuff before, I just thought it would be easier to fit another one as I don't want to start melting things soldering wise anyway. It is my belt recoil or lack of that is the problem with the seat belt but I'm going to give it a clean to see if that helps. I did replace...

Good point! 2001 Terrano 2 2.7tdi electronic speedo. Type with LCD screen above fuel/temp clocks.

Looking for a drivers side front seat belt and also looking for a set of working dash clocks as mine are getting worse. I was doing 110mph and I was parked! it's fast but not that fast.

Interesting way of doing I suppose, but I can't say I have any of them kicking about the garage. I trying not to take it apart to see what size and thread it is as I use it as my daily driver just in case I hit problems.

I have a slight leak near the rear axle and I want to blank the pipe off at the T peace near the bellhousing and was wondering what size and thread is needed for a blanking plug?

Looks really nice, makes mine look really filthy. Saying that I fitted a Kaaz LSD and had to run it in doing figure of eights for half an hour at my mates work on the mucky concrete. And the ute had been sat in the garage for a while getting sanding dust on it, but I do like that shine on yours...

I have an original front bumper, slightly modded and has a winch stashed behind it. It uses the original chassis mount points but I have put 6mm steel plates in and I would say it would be strong enough. http://www.nissan4x4ownersclub.com/forum/showthread.php?t=17442 I have a nicer standard is...

Sure is.. I haven't been on for a while and generally only look at the Terrano pages. :thumbs

Question?? Has anyone ever looked into the legality of fitting a steel bumper? The reason why I ask is that I was told by a 4x4 geek that I should have a cover over my winch rollers just in case of an accident. He said I would be held liable if someone was hurt by my rollers, a pedestrian...

My Ter is 2001 and about 75,000 miles I bought it with 38,000miles on the clock about 6 years ago and take good care of it, it goes on green lanes now and again but no competition use. No rust or corrosion on the chassis to speak of, a bit of surface rust but not much ,it is solid and had very...

I had to take the torsion bar out to get the bolts out, bit of a pain but I have had the torsion bars off before so not too bad to sort out really. Torsion bar mount would have been in the way for welding so had to remove it anyway.

Passengers side is fine and no problems with that just the drivers side seems to be cracked. . The crack was on both sides of the crossmember and I have highlighted in green where the cracks were. I have 4 plug welds and welds along the edges so it should be pretty strong now. .

I should have took some pics before the repair but I will take a pic of it now it is fixed. :doh

I spotted yesterday that where the bottom arm mounts to the diff mount/crossmember bolts together there were stress cracks both sides. I have welded the cracks up and plug welded a 5mm plate in the offending area and thought I would mention it on the forum so other people can check theirs. I...

Cool thanks, not sure why I posted the question as I don't have a passengers side one and I forgot I have a non airbag Momo wheel fitted. :doh

Does it state what year Terranos?

It was an F20 engine out of the S2000 which spins the correct direction I think the engine you mentioned is from front wheel drive car and spins the wrong way.(A Honda thing apparently) I'm digging that front bumper it looks well factory spec. :thumbs

I didn't get chance to finish the Chevette with the S2000 lump in it (long story) but it was fast when I had the 2.0 16V Retop in it, it liked playing with Impreza's on track days. The S2000 engine had been on the dyno and was 260bhp which is probably about 30bhp over the works cars of the day.

Yes it's a Holden with a supercharged LS1 in it. And the car under the cover was my S2000 engined dry sumped Chevette and on throttle bodies which has now gone and been replaced with the ute.

And I know I should really get rid of the rollers and wire rope but I'm too busy spending money on my Ute. :naughty