![]() |
|
Caravan or Towing In this forum you can post anything with regards to caravaning or towing. |
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Senior Member
Join Date: Sep 2014
Location: Yorkshire, J33 M62
Vehicle: 2000 Terrano lwb 2.7TDI
Posts: 5,500
|
![]()
I have started an attempt to educate myself on electrics, specifically 12v, however my brain is refusing to process the information and just seizes up
![]() ![]() I took my old porch light off the caravan as I have another one I want to fit, I didn't realise the new one had no switch and that's when my heart sank. I've bought a switch which I will mount inside on the opposite side of the wall to the light but I'm not sure about these wires..... WP_20170529_13_12_03_Pro.jpg I thought at first there was three different wires but now I believe the pink one is positive and the other two are in fact the same wire (one coming and one going) which is negative. The switch I have has three connections and the new light has two wires. SO... I reckon I need the pink positive and the white and orange negatives to my new switch, which will leave a third connection on the switch, this will be a positive to the new light and the negative from the light will go back to the switch and into the same connection as the white and orange negatives. I apologise if that lot is hard to follow or makes no sense, please help ![]() |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Aug 2008
Location: Devizes Wiltshire
Vehicle: Nissan Note Ntec 1.5
Posts: 14,137
|
![]()
With 12v you can switch either wire
|
![]() |
![]() |
![]() |
#3 |
Senior Member
Join Date: Sep 2004
Location: UK
Posts: 12,965
|
![]()
I reckon Zippy will answer this best. However first of all I'd be testing with a multimeter to check pos and neg.
Your switch must be an illuminating type so will have a pos feed with a switched pos and also a neg, the neg is used for the bulb or led inside the switch. Not a bad idea to use the illumination feature so you'll know when the light has been left on. |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Aug 2008
Location: Devizes Wiltshire
Vehicle: Nissan Note Ntec 1.5
Posts: 14,137
|
![]()
Ill do drawing tomorrow:-)
|
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: Sep 2014
Location: Yorkshire, J33 M62
Vehicle: 2000 Terrano lwb 2.7TDI
Posts: 5,500
|
![]() |
![]() |
![]() |
![]() |
#6 |
Senior Member
Join Date: Aug 2008
Location: Devizes Wiltshire
Vehicle: Nissan Note Ntec 1.5
Posts: 14,137
|
![]() |
![]() |
![]() |
![]() |
#7 | |
Senior Member
Join Date: Sep 2014
Location: Yorkshire, J33 M62
Vehicle: 2000 Terrano lwb 2.7TDI
Posts: 5,500
|
![]() Quote:
20170529_193112.jpg |
|
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: Sep 2004
Location: UK
Posts: 12,965
|
![]()
Could the third wire be a daisy chain of that particular feed to another item in the same way as a ring main on a house.
|
![]() |
![]() |
![]() |
#9 | |
Senior Member
Join Date: Sep 2004
Location: UK
Posts: 12,965
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#10 |
Senior Member
Join Date: Jun 2012
Location: Sevenoaks, Kent
Vehicle: Terrano 2.7TDi SE Touring
Posts: 5,221
|
![]()
Ok, caravans tend to differ to cars, as most do not use the body as a return/earth. So as you guessed, 1 is the positive, and one is the ground... often, on caravans, the White is the ground, but never trust or assume and always meter the wires as some vans do not stick to any of the normal standards.
I would expect the one with 2 wires to be the ground, and as you say, it daisy chains on from your light to another one. Not knowing the specific switch, I would guess it is a change over switch, meaning that one terminal is the common or input, and 1 of the other 2 are connected to it, dependant on which way the switch is pressed. Unless it is an illuminated switch, you very rarely connect the earth to them in low voltage wiring. Sent from my SM-T705 using Tapatalk |
![]() |
![]() |
![]() |
#11 |
Senior Member
Join Date: Sep 2014
Location: Yorkshire, J33 M62
Vehicle: 2000 Terrano lwb 2.7TDI
Posts: 5,500
|
![]() |
![]() |
![]() |
![]() |
#12 |
Senior Member
Join Date: Sep 2014
Location: Yorkshire, J33 M62
Vehicle: 2000 Terrano lwb 2.7TDI
Posts: 5,500
|
![]()
This is the back of the switch, you can just about make out a diagram above the C in the CE mark. If anyone can see it to look at it a translation would be flippin' awesome
![]() WP_20170529_22_01_24_Pro.jpg |
![]() |
![]() |
![]() |
#13 |
Senior Member
Join Date: Jun 2012
Location: Sevenoaks, Kent
Vehicle: Terrano 2.7TDi SE Touring
Posts: 5,221
|
![]()
Yep, that looks like a change over, so the in is on the left of pic, single connector, and then the out is one of the ones on the right, basically 1 will be live with the top of the switch pressed in, and the other when the bottom is.
Sent from my SM-T705 using Tapatalk |
![]() |
![]() |
![]() |
#14 |
Senior Member
Join Date: Sep 2014
Location: Yorkshire, J33 M62
Vehicle: 2000 Terrano lwb 2.7TDI
Posts: 5,500
|
![]()
Magic, so positive in on the left, neg and pos out on the right and a neg from the light back to the neg on switch?
|
![]() |
![]() |
![]() |
#15 | |
Senior Member
Join Date: Jun 2012
Location: Sevenoaks, Kent
Vehicle: Terrano 2.7TDi SE Touring
Posts: 5,221
|
![]() Quote:
Either cut, or better still, pull the Positive wire inside the caravan, and put it in to the left of switch, then connect the positive wire of the new lamp (or a new wire if it does not have wires already), to one of the right connections... one will be left empty.... it does not matter which, as you can put that switch up either way. Sent from my SM-T705 using Tapatalk |
|
![]() |
![]() |
![]() |
|
|