|
|
|
|||||||
| The Clubs Virtual Pub For general chat, so come on in and pull up a chair. |
 |
|
|
Thread Tools | Display Modes |
19-08-2024, 18:36
|
#16 |
|
Off road maniac
 
Join Date: Dec 2009
Location: Bexhill on Sea
Vehicle: Y60 Patrol Me, 3 ltr Mrs
Posts: 17,429
|
Chuck mounted and ready for work
__________________
Ex banger racer now off road maniac  Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare. |
|
|
|
19-08-2024, 18:42
|
#17 |
|
Off road maniac
Join Date: Dec 2009
Location: Bexhill on Sea
Vehicle: Y60 Patrol Me, 3 ltr Mrs
Posts: 17,429
|
Had an old disk laying around, so stuck it on for a test, all good well pleased, but got some vertical milling to do now to make a tool grinder so all this will have to come off again, Rick
__________________
Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare. |
|
|
|
|
20-08-2024, 21:25
|
#18 |
|
Off road maniac
Join Date: Dec 2009
Location: Bexhill on Sea
Vehicle: Y60 Patrol Me, 3 ltr Mrs
Posts: 17,429
|
Have to say I was not too impressed with the finish on the disk, but never having turned such a large item before especially cast iron I did some research and found my spindle speed was a tad high plus on closer inspection the TC insert was dull, it was a new one for the job but guess the rust took the edge off, made another cut today and much better, so having sorted that, time to set it up again for vertical milling
__________________
Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare. |
|
|
|
|
20-08-2024, 21:32
|
#19 |
|
Off road maniac
Join Date: Dec 2009
Location: Bexhill on Sea
Vehicle: Y60 Patrol Me, 3 ltr Mrs
Posts: 17,429
|
Down side of that is the head locating bolts are a little slack so it needed setting up again, side to side I had a difference of 4 thou and front to back 9 thou, the best way I have found is with a long fly cutter, get the bed close and measure with feelers, this way I do not scratch the bed, all sorted now and ready for work, but not tomorrow, I have my injector pump to change, Rick
__________________
Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare. |
|
|
|
|
|
|
Linear Mode
