Terrano / Mistral

navydave86 · 05-03-2024, 19:15

Yes - this is my first post.
I was able to pickup a 1998 Nissan Mistral stateside with 49K on the clock. It had been setting for a very long time.
Within the first day or two the brake pedal became squishy - and after another few day the brake alarm went off.
If I stand on it the brakes work as they should.
The fluid level in the master cylinder has not dropped so I suspect corrosion or a bad seal in the master cylinder.
Could anyone please direct me to a part number for the RHD version of the 1998 Mistral / Terrano.

This one was built in Spain and shipped to Japan. It is extremely clean but appears to have been setting in long term storage before being exported to the US.

I have found the following part number online but would prefer not to order and then find out they do not fit.

Nissan 46010-0F002
Ford 1956522

Please help

solarman216 · 05-03-2024, 19:48

Hi and welcome, before you start changing parts lets see what you have, you say the BF is up to level so good so far, now pump the pedal without the engine running, goes it go hard? the with your foot on the pedal with moderate pressure start the engine, does it go down? let me know Rick

navydave86 · 05-03-2024, 20:16

Rick,

It did exactly as you stated had to pump to get the pedal hard without the engine running, however after starting the pedal pressure dropped slowly and the pedal dropped down. It took a few seconds for it to drop but it did.

Your thoughts,

Dave

solarman216 · 05-03-2024, 20:34

OK that sounds pretty normal, can you explain the problem in more detail, Rick

navydave86 · 05-03-2024, 20:59

Rick,

When I put my foot on the pedal to start the engine -and the engine starts the pedal starts to drop as I am putting it into gear and I have to press really hard to prevent it from creeping forward. When I hit the brakes at normal road speeds the pedal feels soft and the alarm buzzer goes off. The brake warning light on the dash is on all the time.

Thx for your help,

Dave

solarman216 · 05-03-2024, 21:46

The brake warning light is controlled by 3 things, the hand brake, low fluid and vacuum, if it is on all the time then sounds to me like low vacuum, you need to test this with a gauge, Rick

solarman216 · 05-03-2024, 21:48

The pump will be either on the end of the Alternator or driven from the timing gears under the injector pump, Rick

navydave86 · 23-05-2024, 20:10

Okay that problem was solved - bad vacuum pump - replaced.
If possible could you tell me where the Crankshaft Position Sensor is?

I bought an OEM CPS from a Nissan guy in the UAE
Engine is missing sometimes when driving mostly above 80kmh
I bought the 14 pin OBDll which allowed me to scan for faults - CPS related

Google searches say the front cover and others say on the bell housing, slightly behind the rocker cover and offset towards the drivers side.

Much Thanks in Advance

Dave in the States

solarman216 · 24-05-2024, 11:39

Both positions are valid, it depends what fuel pump you have, Bosch it will be on top of the bell housing, Zexel on the timing cover, Rick

05-03-2024, 19:15	#1
navydave86 Junior Member Join Date: Mar 2024 Location: usa Vehicle: 1998 Nissan Mistral Posts: 4	Terrano / Mistral Yes - this is my first post. I was able to pickup a 1998 Nissan Mistral stateside with 49K on the clock. It had been setting for a very long time. Within the first day or two the brake pedal became squishy - and after another few day the brake alarm went off. If I stand on it the brakes work as they should. The fluid level in the master cylinder has not dropped so I suspect corrosion or a bad seal in the master cylinder. Could anyone please direct me to a part number for the RHD version of the 1998 Mistral / Terrano. This one was built in Spain and shipped to Japan. It is extremely clean but appears to have been setting in long term storage before being exported to the US. I have found the following part number online but would prefer not to order and then find out they do not fit. Nissan 46010-0F002 Ford 1956522 Please help

05-03-2024, 19:48	#2
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,431	Hi and welcome, before you start changing parts lets see what you have, you say the BF is up to level so good so far, now pump the pedal without the engine running, goes it go hard? the with your foot on the pedal with moderate pressure start the engine, does it go down? let me know Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

05-03-2024, 20:34	#4
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,431	OK that sounds pretty normal, can you explain the problem in more detail, Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

05-03-2024, 21:46	#6
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,431	The brake warning light is controlled by 3 things, the hand brake, low fluid and vacuum, if it is on all the time then sounds to me like low vacuum, you need to test this with a gauge, Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

05-03-2024, 21:48	#7
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,431	The pump will be either on the end of the Alternator or driven from the timing gears under the injector pump, Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

05-03-2024, 20:16	#3
navydave86 Junior Member Join Date: Mar 2024 Location: usa Vehicle: 1998 Nissan Mistral Posts: 4	Rick, It did exactly as you stated had to pump to get the pedal hard without the engine running, however after starting the pedal pressure dropped slowly and the pedal dropped down. It took a few seconds for it to drop but it did. Your thoughts, Dave

05-03-2024, 20:59	#5
navydave86 Junior Member Join Date: Mar 2024 Location: usa Vehicle: 1998 Nissan Mistral Posts: 4	Rick, When I put my foot on the pedal to start the engine -and the engine starts the pedal starts to drop as I am putting it into gear and I have to press really hard to prevent it from creeping forward. When I hit the brakes at normal road speeds the pedal feels soft and the alarm buzzer goes off. The brake warning light on the dash is on all the time. Thx for your help, Dave

23-05-2024, 20:10	#8
navydave86 Junior Member Join Date: Mar 2024 Location: usa Vehicle: 1998 Nissan Mistral Posts: 4	1998 Nissan Mistral 2.7 TDi Crankshaft Position Sensor location? Okay that problem was solved - bad vacuum pump - replaced. If possible could you tell me where the Crankshaft Position Sensor is? I bought an OEM CPS from a Nissan guy in the UAE Engine is missing sometimes when driving mostly above 80kmh I bought the 14 pin OBDll which allowed me to scan for faults - CPS related Google searches say the front cover and others say on the bell housing, slightly behind the rocker cover and offset towards the drivers side. Much Thanks in Advance Dave in the States

24-05-2024, 11:39	#9
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,431	Both positions are valid, it depends what fuel pump you have, Bosch it will be on top of the bell housing, Zexel on the timing cover, Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.