Found rust issue on roof gutter and rear door

bartoni79 · 12-11-2021, 11:22

Hi All,

Sorry _ I'm not sure if this is the right place to post this....Ive found this on a roof gutter at the rear of a potential new to be acquired Y60 Patrol.
Does this this like a real (& costly problem) and whatAttachment 11999 would be the cost to fix if at all possible? Under £700 or could this be a DIY job with a grinder and rust proofing? Thanks for any advice.

Banshee · 12-11-2021, 12:43

Barrbeast, come in

solarman216 · 12-11-2021, 12:45

Not a structural issue, I would sand blast it and paint it to stop it getting worse, grinding and wire brushing is useless, Rick

bartoni79 · 12-11-2021, 13:04

Great - phew thanks! So not a show stopper and a sub £500 job?

panelbeater · 12-11-2021, 14:30

if you have access to a compressor a cheap sand blasting gun and dry floor stone gap filling sand like used to put between block paving will do the job.just protect any areas you do not want to blast with steel sheet or thick cardboard.then a zink primer to protect bare metal.

bartoni79 · 12-11-2021, 16:38

Cheers!!
How much do you reckon from a body shop? Sadly I don’t have a sand blaster / air compressor..

Thanks

solarman216 · 12-11-2021, 20:22

Not many body shops will sand blast, it would only take 20 mins for a small job like that then paint immediately before flash rusting starts, if you buy my bumper and come to collect it I will blast it for you for £50 including masking up and a first coat of primer, Rick

Banshee · 12-11-2021, 20:46

Quote:

Originally Posted by solarman216

Not many body shops will sand blast, it would only take 20 mins for a small job like that then paint immediately before flash rusting starts, if you buy my bumper and come to collect it I will blast it for you for £50 including masking up and a first coat of primer, Rick

Find me another owners club with an offer as good as that!!!!

I'll wait

bartoni79 · 12-11-2021, 21:47

Hi!! I'm in. Sounds like a great deal!
Thank you!!

panelbeater · 15-11-2021, 18:59

at the layland dealership i was the bodyshop under manager we used to sandblast all repairs befor repair as the only way to get into the tiny places,remember the mini a frames,then a dioxen wash to leave a phrosphate coat then zink primer befor repair.but as rick says finding someone now will be looking for a golden egg so his offer is great and he wont make much money per hr doing that.

bartoni79 · 20-11-2021, 06:29

Thanks panelbeater! I hope to see Rick the best future!!

12-11-2021, 12:43	#2
Banshee Moderator Join Date: Jul 2012 Location: West Midlands Vehicle: 04 2.7 SWB Terrano II Van Posts: 13,526	Barrbeast, come in __________________ Moderator 04' Terrano II SE 2.7 TDi SWB Commercial in Silver - Project Thread Toyo Open Country M/T 33's on 10J Steels, Super Strong Steering Job Navara D22 Snorkel, Front LOKKA, Maunal Hubs, EGR Blank TunitII ECU Chip, 3" Body Lift, 2" Suss Lift, Heat Exchanger Black Interior, 3.0 Borg&Beck Clutch, Eckes Heated Fuel Filter 99' Y61 Patrol GR SE 2.8 TD6 LWB in Blue/Silver - Project Thread Engine Transplant - In Progress!!!

12-11-2021, 12:45	#3
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,429	Not a structural issue, I would sand blast it and paint it to stop it getting worse, grinding and wire brushing is useless, Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

12-11-2021, 20:22	#7
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,429	Not many body shops will sand blast, it would only take 20 mins for a small job like that then paint immediately before flash rusting starts, if you buy my bumper and come to collect it I will blast it for you for £50 including masking up and a first coat of primer, Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

12-11-2021, 13:04	#4
bartoni79 Junior Member Join Date: Nov 2021 Location: South East - Berkshire Vehicle: Nissan Patrol Y60 Posts: 29	Great - phew thanks! So not a show stopper and a sub £500 job?

12-11-2021, 14:30	#5
panelbeater Senior Member Join Date: Dec 2012 Location: clacton on sea essex Vehicle: nissan terrano 2 2.7 tdi Posts: 1,637	if you have access to a compressor a cheap sand blasting gun and dry floor stone gap filling sand like used to put between block paving will do the job.just protect any areas you do not want to blast with steel sheet or thick cardboard.then a zink primer to protect bare metal.

12-11-2021, 16:38	#6
bartoni79 Junior Member Join Date: Nov 2021 Location: South East - Berkshire Vehicle: Nissan Patrol Y60 Posts: 29	Cheers!! How much do you reckon from a body shop? Sadly I don’t have a sand blaster / air compressor.. Thanks

12-11-2021, 21:47	#9
bartoni79 Junior Member Join Date: Nov 2021 Location: South East - Berkshire Vehicle: Nissan Patrol Y60 Posts: 29	Hi!! I'm in. Sounds like a great deal! Thank you!!

15-11-2021, 18:59	#10
panelbeater Senior Member Join Date: Dec 2012 Location: clacton on sea essex Vehicle: nissan terrano 2 2.7 tdi Posts: 1,637	at the layland dealership i was the bodyshop under manager we used to sandblast all repairs befor repair as the only way to get into the tiny places,remember the mini a frames,then a dioxen wash to leave a phrosphate coat then zink primer befor repair.but as rick says finding someone now will be looking for a golden egg so his offer is great and he wont make much money per hr doing that.

20-11-2021, 06:29	#11
bartoni79 Junior Member Join Date: Nov 2021 Location: South East - Berkshire Vehicle: Nissan Patrol Y60 Posts: 29	Thanks panelbeater! I hope to see Rick the best future!!