are thease the bolts i need?

zippy656 · 05-04-2009, 16:28

http://www.namrick.co.uk/browse.asp?PCID=9

M12 1.25mm Pitch 60mm long so i can refit the pig tail too??

Terranosaurus · 05-04-2009, 16:41

Sounds right but don't know for certain - you've got te other pair out.

Are the M12 - ie nominal 12mm diameter

Are the 40mm long

Are they 1.25mm pitch - ie 4 treads per 5mm or 8 threads per 10mm/1cm

zippy656 · 05-04-2009, 17:04

normal M12's nearly fitted. so thats right, just the pitch was rong. the ones i took out are a lot finer, and a local man just looked and said M12 1.25 pitch, we dont have any..sorry mate...

looking at the site. .95p each plus vat. cant see nissan haveing them for same or less...

Jocky · 05-04-2009, 17:38

Have you asked Nissan for the bolts?

I got 2 off them for my ABar and it was only £2 or so, and they ordered them.

zippy656 · 05-04-2009, 18:38

will call tomorrow

tar

P40MRT · 05-04-2009, 18:54

My Avenger A bar has been on for about 5 months and 5000 miles, and I never did get round to buying the extra pair of bolts! Just one each side at the bottom, and then the two little 'straps' between grille and bumper...

rustic · 05-04-2009, 19:00

The bolts are the same as Citroen Picasso wheel bolts, M12 x 1.25 as far as I am aware. When I fitted locking wheel bolts to picasso, I noticed they were the same as the front tapped holes in the maverick, as I was thinking of fitting a front tow bar at the time. Still not fitted one yet though.
May be next year...

zippy656 · 05-04-2009, 19:10

i dont have one that uses the two little 'straps' between grille and bumper...

just the 4 bolts

ssteve · 05-04-2009, 19:45

Quote:

Originally Posted by zippy656

normal M12's nearly fitted. so thats right, just the pitch was rong. the ones i took out are a lot finer, and a local man just looked and said M12 1.25 pitch, we dont have any..sorry mate...

looking at the site. .95p each plus vat. cant see nissan haveing them for same or less...

m12 has 1.75 as std pitch see below
http://www.boltdepot.com/fastener-in...ead-Pitch.aspx

ssteve

Terranosaurus · 05-04-2009, 19:51

Quote:

Originally Posted by ssteve

m12 has 1.75 as std pitch see below
http://www.boltdepot.com/fastener-in...ead-Pitch.aspx

ssteve

Yes it does but Japanese manufacturers use a lot of metric fine hence the question - if you read the thread zippy has already tried a std M12.

ssteve · 05-04-2009, 20:16

Quote:

Originally Posted by Terranosaurus

Yes it does but Japanese manufacturers use a lot of metric fine hence the question - if you read the thread zippy has already tried a std M12.

it must be JIS then
ssteve

zippy656 · 05-04-2009, 20:25

oh yes tryed that, on my back with the A Bar in one hand the other holding the spacers and the other holding my sockets..

yep ive got three hands!

scott301004 · 05-04-2009, 21:09

I have used M12 X 1.25mm pitch with the front tow bars

zippy656 · 05-04-2009, 21:11

well your the man whod know..

thanks scot..

scott301004 · 05-04-2009, 21:15

and i got them from namrick as they are pretty good with delivery and price

05-04-2009, 16:28	#1
zippy656 Senior Member Join Date: Aug 2008 Location: Devizes Wiltshire Vehicle: Nissan Note Ntec 1.5 Posts: 14,138	are thease the bolts i need? http://www.namrick.co.uk/browse.asp?PCID=9 M12 1.25mm Pitch 60mm long so i can refit the pig tail too??

05-04-2009, 17:38	#4
Jocky Senior Member Join Date: Feb 2005 Location: Teesside,Englandshire, I only sleep there honest. Vehicle: Nissan Patrol 2.8 TD6 Y61 Posts: 1,420	Have you asked Nissan for the bolts? I got 2 off them for my ABar and it was only £2 or so, and they ordered them. __________________ (Y61) Patrol 2.8TD6 SE Touring.DPT Box. Ironman Nitro Shocks OME Springs 20mm lift front, 30mm lift rear. 33" General Grabber AT's, Airtec Snorkel, EGR Mod. 2.5" Stainless Exhaust

05-04-2009, 19:00	#7
rustic Senior Member Join Date: Feb 2007 Location: Staffordshire Vehicle: Maverick Mk I 2.7 TD LWB Posts: 7,825	The bolts are the same as Citroen Picasso wheel bolts, M12 x 1.25 as far as I am aware. When I fitted locking wheel bolts to picasso, I noticed they were the same as the front tapped holes in the maverick, as I was thinking of fitting a front tow bar at the time. Still not fitted one yet though. May be next year... __________________ Ford Maverick GLX 1995 2.7TD LWB in illusion silver, 98k miles. Owned since new, for 22 years. Best car I have ever owned. Just wish I could drive it more.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-04-2009, 16:41	#2
Terranosaurus Senior Member Join Date: Aug 2006 Location: YORKSHIRE Vehicle: 2001 2.7 TDi T2 SWB Posts: 4,077	Sounds right but don't know for certain - you've got te other pair out. Are the M12 - ie nominal 12mm diameter Are the 40mm long Are they 1.25mm pitch - ie 4 treads per 5mm or 8 threads per 10mm/1cm

05-04-2009, 17:04	#3
zippy656 Senior Member Join Date: Aug 2008 Location: Devizes Wiltshire Vehicle: Nissan Note Ntec 1.5 Posts: 14,138	normal M12's nearly fitted. so thats right, just the pitch was rong. the ones i took out are a lot finer, and a local man just looked and said M12 1.25 pitch, we dont have any..sorry mate... looking at the site. .95p each plus vat. cant see nissan haveing them for same or less...

05-04-2009, 18:38	#5
zippy656 Senior Member Join Date: Aug 2008 Location: Devizes Wiltshire Vehicle: Nissan Note Ntec 1.5 Posts: 14,138	will call tomorrow tar

05-04-2009, 18:54	#6
P40MRT Senior Member Join Date: Oct 2008 Location: Milton Keynes, Buckinghamshire Vehicle: '98 Maverick TDi SWB Posts: 108	My Avenger A bar has been on for about 5 months and 5000 miles, and I never did get round to buying the extra pair of bolts! Just one each side at the bottom, and then the two little 'straps' between grille and bumper...

05-04-2009, 19:10	#8
zippy656 Senior Member Join Date: Aug 2008 Location: Devizes Wiltshire Vehicle: Nissan Note Ntec 1.5 Posts: 14,138	i dont have one that uses the two little 'straps' between grille and bumper... just the 4 bolts

05-04-2009, 20:25	#12
zippy656 Senior Member Join Date: Aug 2008 Location: Devizes Wiltshire Vehicle: Nissan Note Ntec 1.5 Posts: 14,138	oh yes tryed that, on my back with the A Bar in one hand the other holding the spacers and the other holding my sockets.. yep ive got three hands!

05-04-2009, 21:09	#13
scott301004 Senior Member Join Date: Nov 2008 Location: Burton on trent Vehicle: Range Rover DSE Posts: 242	I have used M12 X 1.25mm pitch with the front tow bars

05-04-2009, 21:11	#14
zippy656 Senior Member Join Date: Aug 2008 Location: Devizes Wiltshire Vehicle: Nissan Note Ntec 1.5 Posts: 14,138	well your the man whod know.. thanks scot..

05-04-2009, 21:15	#15
scott301004 Senior Member Join Date: Nov 2008 Location: Burton on trent Vehicle: Range Rover DSE Posts: 242	and i got them from namrick as they are pretty good with delivery and price