Scrapping T2

solarman216 · 27-10-2014, 23:32

Hi all I have several T2's here that I am breaking, before I take em down the scrap yard, so if you need a part say so soon you have a week or two, Rick

Lazy-Ferret · 27-10-2014, 23:38

Quote:

Originally Posted by solarman216

Hi all I have several T2's here that I am breaking, before I take em down the scrap yard, so if you need a part say so soon you have a week or two, Rick

Don't suppose you have an intercooler??? one that is not bent to pieces or leaking? Suz says she is hoping 3rd time lucky!

AlexD333 · 27-10-2014, 23:39

Quote:

Originally Posted by solarman216

Hi all I have several T2's here that I am breaking, before I take em down the scrap yard, so if you need a part say so soon you have a week or two, Rick

Steering mod bits please. Prob some more bits, you'll know better than me

Infact maybe we can just weld the scrapper to mine

solarman216 · 27-10-2014, 23:42

Quote:

Originally Posted by Lazy-Ferret

Don't suppose you have an intercooler??? one that is not bent to pieces or leaking? Suz says she is hoping 3rd time lucky!

yep have a good one, Rick

terrano bob · 27-10-2014, 23:44

:don't sell anything yet rick ive heard alex might be off roading soon

AlexD333 · 27-10-2014, 23:45

Quote:

Originally Posted by terrano bob

:don't sell anything yet rick ive heard alex might be off roading soon

unfortunately Rick is always the one to see the aftermath of my mishaps

terrano bob · 27-10-2014, 23:47

l:

Quote:

Originally Posted by AlexD333

unfortunately Rick is always the one to see the aftermath of my mishaps

Lazy-Ferret · 27-10-2014, 23:47

Quote:

Originally Posted by solarman216

yep have a good one, Rick

How much are you looking for? So far my luck is not going well, the last one I got arrived looking like this after the post office played pass the parcel

This should be round

Note the curved (used to be straight) edge

and the cover...

I think we would pop down and collect your one.

terrano bob · 27-10-2014, 23:50

Quote:

Originally Posted by Lazy-Ferret

How much are you looking for? So far my luck is not going well, the last one I got arrived looking like this after the post office played pass the parcel

This should be round

Note the curved (used to be straight) edge

and the cover...

I think we would pop down and collect your one.

that's bad

Sweety · 27-10-2014, 23:54

Hope you put a claim in for that damage Clive

Lazy-Ferret · 28-10-2014, 00:06

My intercooler was leaking where the cross tubes join the end castings... I looked into getting it repaired, but silly money, so I scrapped away and used liquid metal to repair. The problem was, the aluminium has corroded and turned to flaky white stuff, so as I repaired one leak, I created another. I got it sealed up, but it was a bit iffy, so I ordered one replacement one off Ebay. Stupidly, and mine was still OK, and I had a few other jobs under way, when it arrived, I checked it over, and it seemed OK and nice and clean. Once I got around to fitting it, it also had a leak, worse than my old one, but this time right up in the middle of the matrix, and impossible to get to. The trouble was, I left it too long between ordering and fitting to make a claim.

I ordered this one as a second replacement, and as you can see, they wrecked it, so the person who sent it, is in the process of putting in a claim, and we will wait and see, but based on past experience, I have never had a courier take the blame once, so I won't hold my breath.

Gave it a good beating though to inflict all that on it. I was thinking of seeing if it would pressure test, just out of curiosity...

AlexD333 · 28-10-2014, 00:22

Yeah it doesent go that shape by itself... They must have been lobbing it about, quite literally

solarman216 · 28-10-2014, 01:05

Quote:

Originally Posted by Lazy-Ferret

How much are you looking for? So far my luck is not going well, the last one I got arrived looking like this after the post office played pass the parcel

This should be round

Note the curved (used to be straight) edge

and the cover...

I think we would pop down and collect your one.

no reasonable offer refused, come have a look, rather than post, will hold till you have been, Rick

Fez_uk · 28-10-2014, 10:03

That is poorly packed, should of cone in a decent box, would of still cost the same by courier.

t2chris · 28-10-2014, 10:21

Got any crank position sensors that go into the front of the chest mate?

Intercooler football is the new craze clive lol, but hope royal mail give you money back mate!

27-10-2014, 23:32	#1
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,432	Scrapping T2 Hi all I have several T2's here that I am breaking, before I take em down the scrap yard, so if you need a part say so soon you have a week or two, Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

27-10-2014, 23:44	#5
terrano bob Senior Member Join Date: Sep 2013 Location: north west Vehicle: nissan terrano 2 2.7tdi Posts: 1,015	:don't sell anything yet rick ive heard alex might be off roading soon

27-10-2014, 23:54	#10
Sweety Senior Member Join Date: May 2013 Location: Northumberland Vehicle: Terrano 2.7TDI SE LWB Posts: 3,604	Hope you put a claim in for that damage Clive

28-10-2014, 00:06	#11
Lazy-Ferret Senior Member Join Date: Jun 2012 Location: Sevenoaks, Kent Vehicle: Terrano 2.7TDi SE Touring Posts: 5,221	My intercooler was leaking where the cross tubes join the end castings... I looked into getting it repaired, but silly money, so I scrapped away and used liquid metal to repair. The problem was, the aluminium has corroded and turned to flaky white stuff, so as I repaired one leak, I created another. I got it sealed up, but it was a bit iffy, so I ordered one replacement one off Ebay. Stupidly, and mine was still OK, and I had a few other jobs under way, when it arrived, I checked it over, and it seemed OK and nice and clean. Once I got around to fitting it, it also had a leak, worse than my old one, but this time right up in the middle of the matrix, and impossible to get to. The trouble was, I left it too long between ordering and fitting to make a claim. I ordered this one as a second replacement, and as you can see, they wrecked it, so the person who sent it, is in the process of putting in a claim, and we will wait and see, but based on past experience, I have never had a courier take the blame once, so I won't hold my breath. Gave it a good beating though to inflict all that on it. I was thinking of seeing if it would pressure test, just out of curiosity...

28-10-2014, 00:22	#12
AlexD333 Senior Member Join Date: Jan 2014 Location: Uk Vehicle: 2004 Terrano 2.7 TDI Posts: 7,847	Yeah it doesent go that shape by itself... They must have been lobbing it about, quite literally

28-10-2014, 10:03	#14
Fez_uk Senior Member Join Date: Sep 2010 Location: Mid-Wales Vehicle: Maverick 2.7 - Patrol 4.2 Posts: 5,644	That is poorly packed, should of cone in a decent box, would of still cost the same by courier.

28-10-2014, 10:21	#15
t2chris Senior Member Join Date: Sep 2014 Location: Kent Vehicle: Terrano 2 lwb 2.7tdi se+ Posts: 129	Got any crank position sensors that go into the front of the chest mate? Intercooler football is the new craze clive lol, but hope royal mail give you money back mate!