Advice for the 2nd speed hole

R1cho · 15-04-2014, 22:52

ok i need a bit of advice for this one, the 2nd speed hole

would it be better to plate it from underneath, or like i did the 1st one, from the top, also is it easy to remove the gay bs pump and put it back on? i know i am going to need to remove it if i go in from the top but what if i go from under neath, cut the bolts off make new holes and rebolt into the new plate?

makeitfit · 15-04-2014, 23:04

How bad is it where it joins the bulkhead ?
I found it best to plate on the underside and dress from the top.
Nice clean under body to stop mud getting in again. You can hammer down the top side and weld again. Then seam seal and paint as usual. I'd guess the gay pump could be lifted a bit by carefully unclipping the brake lines first

R1cho · 15-04-2014, 23:07

i've not checked the bulkhead yet as i need to take the wheel off to get in and have a proper look, today to protect it from weld spatter from above i put a sheet of metal over it

hmmm seam sealer, spose i should get some of that, will take a few days off egay tho, and i need to get it done this week/end

makeitfit · 15-04-2014, 23:13

Motor factors in Carmarthen will have it

R1cho · 15-04-2014, 23:13

Quote:

Originally Posted by makeitfit

Motor factors in Carmarthen will have it

the one on the hill?

makeitfit · 15-04-2014, 23:14

something Morgan

R1cho · 15-04-2014, 23:15

john

R1cho · 15-04-2014, 23:20

right then, i'll go in from underneath, cut the bolts off and redrill the new plate, seam seal and then chaiss black the entire inner wheel arch, before bolting the gaybs back down and the fuel filter holder i'll seam seal the inside and chassis black it aswell then rebolt them back down, that should make it good for a few years

exosteve · 15-04-2014, 23:34

watchin with interst

Fez_uk · 15-04-2014, 23:40

Swear mavericks seem to rust less than terranos. No ABS either ooooopshh.

Goodluck butt.

makeitfit · 15-04-2014, 23:46

Quote:

Originally Posted by Fez_uk

Swear mavericks seem to rust less than terranos. No ABS either ooooopshh.

Goodluck butt.

I wish

Mine's a maverick and has no gay pump

About the only thing we haven't bloody welded is the sunroof

Fez_uk · 15-04-2014, 23:48

Maybe i've just been lucky??

R1cho · 15-04-2014, 23:50

Quote:

Originally Posted by makeitfit

About the only thing we haven't bloody welded is the sunroof

don't you mean....manly escape hatch

makeitfit · 15-04-2014, 23:51

Quote:

Originally Posted by R1cho

don't you mean....manly escape hatch

that's the fella

15-04-2014, 22:52	#1
R1cho Senior Member Join Date: Aug 2010 Location: Wales Vehicle: 1997 LandCruiser Colorado Posts: 4,201	Advice for the 2nd speed hole ok i need a bit of advice for this one, the 2nd speed hole would it be better to plate it from underneath, or like i did the 1st one, from the top, also is it easy to remove the gay bs pump and put it back on? i know i am going to need to remove it if i go in from the top but what if i go from under neath, cut the bolts off make new holes and rebolt into the new plate?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

15-04-2014, 23:04	#2
makeitfit Senior Member Join Date: Apr 2008 Location: on the beach WEST WALES Vehicle: Maverick TDi BLACK mmm Posts: 15,136	How bad is it where it joins the bulkhead ? I found it best to plate on the underside and dress from the top. Nice clean under body to stop mud getting in again. You can hammer down the top side and weld again. Then seam seal and paint as usual. I'd guess the gay pump could be lifted a bit by carefully unclipping the brake lines first

15-04-2014, 23:07	#3
R1cho Senior Member Join Date: Aug 2010 Location: Wales Vehicle: 1997 LandCruiser Colorado Posts: 4,201	i've not checked the bulkhead yet as i need to take the wheel off to get in and have a proper look, today to protect it from weld spatter from above i put a sheet of metal over it hmmm seam sealer, spose i should get some of that, will take a few days off egay tho, and i need to get it done this week/end

15-04-2014, 23:13	#4
makeitfit Senior Member Join Date: Apr 2008 Location: on the beach WEST WALES Vehicle: Maverick TDi BLACK mmm Posts: 15,136	Motor factors in Carmarthen will have it

15-04-2014, 23:14	#6
makeitfit Senior Member Join Date: Apr 2008 Location: on the beach WEST WALES Vehicle: Maverick TDi BLACK mmm Posts: 15,136	something Morgan

15-04-2014, 23:15	#7
R1cho Senior Member Join Date: Aug 2010 Location: Wales Vehicle: 1997 LandCruiser Colorado Posts: 4,201	john

15-04-2014, 23:20	#8
R1cho Senior Member Join Date: Aug 2010 Location: Wales Vehicle: 1997 LandCruiser Colorado Posts: 4,201	right then, i'll go in from underneath, cut the bolts off and redrill the new plate, seam seal and then chaiss black the entire inner wheel arch, before bolting the gaybs back down and the fuel filter holder i'll seam seal the inside and chassis black it aswell then rebolt them back down, that should make it good for a few years

15-04-2014, 23:34	#9
exosteve Senior Member Join Date: Dec 2012 Location: stoke on trent Vehicle: 2001 2.7 td lwb terrano Posts: 2,740	watchin with interst

15-04-2014, 23:40	#10
Fez_uk Senior Member Join Date: Sep 2010 Location: Mid-Wales Vehicle: Maverick 2.7 - Patrol 4.2 Posts: 5,645	Swear mavericks seem to rust less than terranos. No ABS either ooooopshh. Goodluck butt.

15-04-2014, 23:48	#12
Fez_uk Senior Member Join Date: Sep 2010 Location: Mid-Wales Vehicle: Maverick 2.7 - Patrol 4.2 Posts: 5,645	Maybe i've just been lucky??