POST WHAT YOU ARE DOING NOW! no fibbing - Page 10

jims-terrano · 20-05-2013, 17:59

Well I'm sat here thinking how I can remove the old snapped bolts from the side step mountings as I want to put them back on again. Not that I can do much at the moment other than sit and think about it.
Also thinking about removing the osf wing and bumper to get to the washer pump so that I can replace it. Again can't do much else other than think about it at the mo

melissachels · 20-05-2013, 18:40

just waiting on my daughter to finish her dinner then its bed for her, & i can get these accounts corrected, boring me as per

darryl · 20-05-2013, 18:42

enjoying a pint

(RIP) rustygates · 20-05-2013, 18:54

Quote:

Originally Posted by jims-terrano

Well I'm sat here thinking how I can remove the old snapped bolts from the side step mountings as I want to put them back on again. Not that I can do much at the moment other than sit and think about it.
Also thinking about removing the osf wing and bumper to get to the washer pump so that I can replace it. Again can't do much else other than think about it at the mo

Hi,no need to remove front bumper unless you really need to,did mine couple of weeks ago,washer bottle is in 2 halves under wing bottle fits via "O" ring into under bonnet bit, bolt are difficult to get to.

rustygates.

jims-terrano · 20-05-2013, 19:15

Interesting how did you do it???

I found what I thought were the bolts, stuck through inner wing in engine bay. The nut's were stuck on to them and they just spun around so the nuts would slacken off.

briggie · 20-05-2013, 19:18

Quote:

Originally Posted by rustygates

Hi,no need to remove front bumper unless you really need to,did mine couple of weeks ago,washer bottle is in 2 halves under wing bottle fits via "O" ring into under bonnet bit, bolt are difficult to get to.

rustygates.

can you explain in more detail please ?

ClanWolf · 21-05-2013, 02:12

Still writing.

(RIP) rustygates · 23-05-2013, 05:04

When the wing came off, i wanted to remove the washer bottle and i think there are 3 nuts in the inner wing 2 came off ok but 1 was turning and i got the chisel between bottle and inner wing and cut it, replaced bottle with 2bolts

(RIP) rustygates · 23-05-2013, 05:04

finally

(RIP) rustygates · 23-05-2013, 05:07

bolt holes

jims-terrano · 23-05-2013, 08:32

Rusty, what you painting it with??????

(RIP) rustygates · 23-05-2013, 14:19

Hi, I start by cleaning everything,then red oxide after that under seal mixed with waxoil sprayed give it 3 coats and it also gives it a shiny finish.

jims-terrano · 23-05-2013, 14:21

Quote:

Originally Posted by rustygates

Hi, I start by cleaning everything,then red oxide after that under seal mixed with waxoil sprayed give it 3 coats and it also gives it a shiny finish.

Hmm fancy doing mine now

96terrano · 23-05-2013, 14:22

I'm listening to fleetwood mac in mums car whilst she does the shopping

jims-terrano · 23-05-2013, 14:26

Quote:

Originally Posted by 96terrano

I'm listening to fleetwood mac in mums car whilst she does the shopping

I'm just trying to summon up enough enthusiasm to do some course work but that's boring

I've got until the end of May to get two modules of a course finished and handed in.
But the work is so dulllllllllllllll

:co nfused:

23-05-2013, 14:19	#147
(RIP) rustygates Senior Member Join Date: Jul 2005 Location: N wales Vehicle: 1997 swb + 2003 swb tdi Posts: 672	Hi, I start by cleaning everything,then red oxide after that under seal mixed with waxoil sprayed give it 3 coats and it also gives it a shiny finish. __________________ 1997 Terrano 2.7tdi se red/silver swb. 130k . A-frame+spots, privacy glass, tyres 235-70rx15 BF Goodrich a/t ko pulling a 2005 Bailey vendee series5 with powrtouch mover. 2003 Terrano 2.7tdi se ruby red/silver 74k

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

20-05-2013, 17:59	#136
jims-terrano Senior Member Join Date: Sep 2004 Location: UK Posts: 12,965	Well I'm sat here thinking how I can remove the old snapped bolts from the side step mountings as I want to put them back on again. Not that I can do much at the moment other than sit and think about it. Also thinking about removing the osf wing and bumper to get to the washer pump so that I can replace it. Again can't do much else other than think about it at the mo

20-05-2013, 18:40	#137
melissachels Senior Member Join Date: Mar 2012 Location: Near Armagh, Northern Ireland Vehicle: half of a T2 2.7td swb Posts: 1,216	just waiting on my daughter to finish her dinner then its bed for her, & i can get these accounts corrected, boring me as per

20-05-2013, 18:42	#138
darryl Senior Member Join Date: Sep 2012 Location: malvern Vehicle: maverick 2.7td Posts: 583	enjoying a pint

20-05-2013, 19:15	#140
jims-terrano Senior Member Join Date: Sep 2004 Location: UK Posts: 12,965	Interesting how did you do it??? I found what I thought were the bolts, stuck through inner wing in engine bay. The nut's were stuck on to them and they just spun around so the nuts would slacken off.

21-05-2013, 02:12	#142
ClanWolf Senior Member Join Date: Oct 2009 Location: West Sussex Vehicle: Terrano II 2.4i SE Posts: 319	Still writing.

23-05-2013, 08:32	#146
jims-terrano Senior Member Join Date: Sep 2004 Location: UK Posts: 12,965	Rusty, what you painting it with??????

23-05-2013, 14:22	#149
96terrano Senior Member Join Date: Jun 2010 Location: Dumfries and Galloway, Scotland Vehicle: Nissan Terrano 2.7TD LWB Posts: 8,024	I'm listening to fleetwood mac in mums car whilst she does the shopping