Leaning Towards Standard Pics. - Page 2

makeitfit · 11-01-2017, 12:56

Quote:

Originally Posted by Banshee

I'll take a look at mine later, pretty sure it's not been done but maybe a mod for the list

I presume this is restrictive and once opened up works better?

Yes mate the std nissan bend off the turbo is very restrictive .
If yours has been done then you have a good system

makeitfit · 11-01-2017, 13:02

Turbo back is essentially the front down pipe. That's off the back of the turbo but the back of the turbo is the problem. You need a flange back job

Can't find a pic quickly but look at the pic here off fleabay to see what I mean.
http://www.ebay.co.uk/itm/NISSAN-TER...8AAOSwux5YNtGk

Banshee · 11-01-2017, 14:42

Quote:

Originally Posted by makeitfit

Turbo back is essentially the front down pipe. That's off the back of the turbo but the back of the turbo is the problem. You need a flange back job

Can't find a pic quickly but look at the pic here off fleabay to see what I mean.
http://www.ebay.co.uk/itm/NISSAN-TER...8AAOSwux5YNtGk

I don't even have any ideas as to how I'd even begin to start modifying that to take the elbow out

You'll have to send me some pics dude when you get 5

Lazy-Ferret · 11-01-2017, 15:11

Quote:

Originally Posted by Banshee

I don't even have any ideas as to how I'd even begin to start modifying that to take the elbow out

You'll have to send me some pics dude when you get 5

He did a whole thread on it.... Here........

luke1987 · 11-01-2017, 16:32

Thanks for the info makeitfit. Funny thing is I can weld but dont have a tig only a mig, I might bite the bullet and get some stainless wire and tri mix gas and do it myself or the other option do the full thing in mild steel and coat it with VHT paint.

makeitfit · 12-01-2017, 00:40

Quote:

Originally Posted by luke1987

Thanks for the info makeitfit. Funny thing is I can weld but dont have a tig only a mig, I might bite the bullet and get some stainless wire and tri mix gas and do it myself or the other option do the full thing in mild steel and coat it with VHT paint.

You can weld it with mig and galv spray the welds OR as you say get a small reel of stainless wire and a little gas bottle . Away you go.
I got a box of reject bends off ebay when I did mine. Used the few bends I needed and sold the rest on for more dosh

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-01-2017, 13:02	#17
makeitfit Senior Member Join Date: Apr 2008 Location: on the beach WEST WALES Vehicle: Maverick TDi BLACK mmm Posts: 15,136	Turbo back is essentially the front down pipe. That's off the back of the turbo but the back of the turbo is the problem. You need a flange back job Can't find a pic quickly but look at the pic here off fleabay to see what I mean. http://www.ebay.co.uk/itm/NISSAN-TER...8AAOSwux5YNtGk

11-01-2017, 16:32	#20
luke1987 Senior Member Join Date: Sep 2015 Location: Manchester Vehicle: Nissan Terrano 2.7 SE LWB Posts: 258	Thanks for the info makeitfit. Funny thing is I can weld but dont have a tig only a mig, I might bite the bullet and get some stainless wire and tri mix gas and do it myself or the other option do the full thing in mild steel and coat it with VHT paint.