A Bit Quiet Today?

[elty001]

I'm currently on holiday in Wales
Will post some pics for you when I get a decent signal.

[Terrano Steve]

Originally Posted by solarman216

I got a call to a leaning gable end wall getting read0 y to part company from the house, contacted my scaffold guy to go and shore it up, then got on with my off roader to get ready for next WE at Boxgrove, the very last before they use it as a land fill, discovered water had got into the NSF hub and the inner race is rusted solid onto the stub axle, the drive shaft is busted and the idler stuffed, as well as all the ball joints bad, just as well I have donor motors to rob, but it is all time, then I still have the rear brakes to sort, the winch alternator, the rear winch, (making terrible noises) and yet again the starter is playing up, on top of that the steak house has a blocked drain, (I know it is going to be a dig up job) I did say about it while we were doing the referb but there was not enough time, and as it was only for the Bar basin and coffee machine it did not seem a problem but I have since learnt that coffee grounds harden like concrete, so it has to be a dig up to sort the restriction and it is right at the front of the shop, so on the day I have until 5pm to do the dig repair the pipe and get it all back together, and I am supposed to be retired, happy days, Oh and it is Friday everyone is up the pub etc on a night out cept me, got to be up early to look at a job with some top knobs, Rick

Shame I am not a little closer as I have a drain jetter, works very well & is always worth a try before digging out a drain.

[solarman216]

Originally Posted by Terrano Steve

Shame I am not a little closer as I have a drain jetter, works very well & is always worth a try before digging out a drain.

Thanks for the offer, but I have one of those too, problem is the pipe is only 2 inch and runs under the shop floor and as the blockage is on the outside of the shop where the 2 inch changes to 90 copper bend down into an old 4 inc cast pipe, so jetting from the MH end is not possible, and jetting from in the shop posses the problem of water/gunge disposal as well as the smell, the only reason we did not change this at the beginning was because this pipe took all the main kitchen sinks etc and it seemed to flow OK when we tested it, I am looking at the possibility of moleing a new pipe into an internal MH which is only about 4 ft away I can make an excavation behind the bar as the floor is separate, but cannot afford to touch the wood floor in the shop, Rick

[briggie]

I'm on my jollies in Norfolk

[jims-terrano]

Originally Posted by briggie

I'm on my jollies in Norfolk

Argh that'll be it

[AlexD333]

my eyes have melted from gun club and playing first person shooters on the pc

[Daemo]

Everyone has secretly gone to the billing aquadrome LAND ROVER show

[rustic]

Originally Posted by Daemo

Everyone has secretly gone to the billing aquadrome LAND ROVER show

I would like to say that I have not gone to that show lol...

[Terrano Steve]

Originally Posted by Daemo

Everyone has secretly gone to the billing aquadrome LAND ROVER show

I too would like to say that I have not gone to this show.
Good post though I think most members will want to be denying attending afore mentioned show.

[AlexD333]

Originally Posted by Daemo

Everyone has secretly gone to the billing aquadrome LAND ROVER show

looks like everyone will be getting taxis back as the rust will spread to our motors contagious you see

[johnb5177]

Originally Posted by Terrano Steve

I too would like to say that I have not gone to this show.
Good post though I think most members will want to be denying attending afore mentioned show.

Does this mean, that there are closet.....`landrians`...…on this forum.......

[rustic]

Originally Posted by johnb5177

Does this mean, that there are closet.....`landrians`...…on this forum.......

Well you can strike off all those members who have responded today lol.

It must be the others then...

[spinna]

Closet landrians..... Where

Sent from my SM-G900F using Tapatalk

[jims-terrano]

Phew took me ages to get out of the car park, like an ice ring with all that oil over the roads.

[Daemo]

I have to admit I went on friday and again today I hang my head in shame but I am getting help for this...ripped both indicators out and near side wing came off when I hit the mud run with WAY TOO MUCH enthusiasm, but I do still have my bobtailed rangie so kind of justifies my weekend...