Latest project started Monday to keep me busy - Page 6

terranosaurusdoug · 29-09-2017, 00:49

Quote:

Originally Posted by solarman216

Yes one piece of 6mm ply well whetted first, think Dave used 4mm ply for back shelves, the flat sections of the bar will be tiled, the curved section will be zinc, same as bar top, Rick

6mm

bloody 'ell that is quite thick really, that's twice in one week I've been impressed now

Banshee · 29-09-2017, 08:11

That curved section is quality workmanship!!!!!

Awesome transformation Rick

danielj · 29-09-2017, 11:55

Looking forward to seeing final product. Some tasty craftsmanship there.

solarman216 · 29-09-2017, 21:17

More progress today, this is Sarah mixing, boy does she know how to mix

solarman216 · 29-09-2017, 21:18

Screed done all 18 bags of it

solarman216 · 29-09-2017, 21:31

This turned out to be very interesting, not wanting the drips from the leaking roof on my new screed I pulled the ceiling down and fixed a temp off-cut of plasterboard to absorb the drips, but once exposed I stuck my hand in to see what sort of beam was in there as the box never looked straight, to my horror the box is empty, absolutely nothing to support the cavity wall above nor the ceiling/flat roof joists this side of the box, needless to say this will be ripped out and a beam inserted toot sweet next week, we have decided to renew the whole roof with a completely new structure approx 95 sq mtrs, more on that next week with pics of how it is now and you will see why we are going down this route

solarman216 · 29-09-2017, 21:38

Close up for Tdoug of the curved bar, Oh and it was 4mm ply not 6 never good remembering numbers

solarman216 · 29-09-2017, 21:39

Another shot

solarman216 · 29-09-2017, 21:40

Floor joists in raised area

solarman216 · 29-09-2017, 21:43

From the other end

solarman216 · 29-09-2017, 21:45

CCTV cabling going in, that is it for this week, Rick

terranosaurusdoug · 29-09-2017, 22:40

Thats quite a tight bend, all one piece too, I'm liking that

Was the wood submerged for a period of time of sprayed or what Rick?

solarman216 · 29-09-2017, 23:07

Just laid it on the floor and brushed water over it both sides for a couple of hours, was a little impatient and should have given it another couple of hours and more water but time is at a premium here and if you look close there is the beginning of a crack about the middle, but as it is the backing for what I would call rough joined zinc it will not be a problem, Rick

terranosaurusdoug · 29-09-2017, 23:33

Looking forward to seeing the zinc, I can't picture it in my head.

solarman216 · 02-10-2017, 19:27

Got started on the new roof today, as you can see with so many junctions it is a nightmare to keep water tight, but the lads did well to get this far bearing in mind we did not get the timber till gone midday

29-09-2017, 08:11	#77
Banshee Moderator Join Date: Jul 2012 Location: West Midlands Vehicle: 04 2.7 SWB Terrano II Van Posts: 13,526	That curved section is quality workmanship!!!!! Awesome transformation Rick __________________ Moderator 04' Terrano II SE 2.7 TDi SWB Commercial in Silver - Project Thread Toyo Open Country M/T 33's on 10J Steels, Super Strong Steering Job Navara D22 Snorkel, Front LOKKA, Maunal Hubs, EGR Blank TunitII ECU Chip, 3" Body Lift, 2" Suss Lift, Heat Exchanger Black Interior, 3.0 Borg&Beck Clutch, Eckes Heated Fuel Filter 99' Y61 Patrol GR SE 2.8 TD6 LWB in Blue/Silver - Project Thread Engine Transplant - In Progress!!!

29-09-2017, 23:07	#88
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,431	Just laid it on the floor and brushed water over it both sides for a couple of hours, was a little impatient and should have given it another couple of hours and more water but time is at a premium here and if you look close there is the beginning of a crack about the middle, but as it is the backing for what I would call rough joined zinc it will not be a problem, Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

29-09-2017, 11:55	#78
danielj Senior Member Join Date: Sep 2009 Location: Ireland Vehicle: Terrano 2.7TDI 03 LWB Posts: 695	Looking forward to seeing final product. Some tasty craftsmanship there.

29-09-2017, 22:40	#87
terranosaurusdoug Senior Member Join Date: Sep 2014 Location: Yorkshire, J33 M62 Vehicle: 2000 Terrano lwb 2.7TDI Posts: 5,500	Thats quite a tight bend, all one piece too, I'm liking that Was the wood submerged for a period of time of sprayed or what Rick?

29-09-2017, 23:33	#89
terranosaurusdoug Senior Member Join Date: Sep 2014 Location: Yorkshire, J33 M62 Vehicle: 2000 Terrano lwb 2.7TDI Posts: 5,500	Looking forward to seeing the zinc, I can't picture it in my head.