Latest project started Monday to keep me busy - Page 5

solarman216 · 28-09-2017, 20:11

Top end of raised area

solarman216 · 28-09-2017, 20:14

Would you believe two steels are up here and this end had a bearing of just 2 inches on a brick that itself was overhanging, these engineering bricks will sort it

solarman216 · 28-09-2017, 20:16

Kitchen floor blacked ready for final screed tomorrow and walls lined with S/S

solarman216 · 28-09-2017, 20:17

Bar side of rear wall

solarman216 · 28-09-2017, 20:19

Rear end of bar wall

solarman216 · 28-09-2017, 20:22

New stud to provide new gents WC and small office and screen WC doors from eating area, the disable WC for instance was straight on to food area, not allowed

solarman216 · 28-09-2017, 20:24

Curved shelving in bar

solarman216 · 28-09-2017, 20:26

New office doorway with new gents on the right past the disable WC

solarman216 · 28-09-2017, 20:28

Ladies on the right gents on the left

solarman216 · 28-09-2017, 20:31

Gents in what was the freezer room

solarman216 · 28-09-2017, 20:32

From inside new gents, more tomorrow folks, Rick

terranosaurusdoug · 28-09-2017, 22:07

Any chance of some close ups of the curve round the bar?

solarman216 · 28-09-2017, 22:33

Will take some tomorrow if I remember, the bar or the shelving? I think it is going to be covered with zinc the same as the bar top, with folded joins! Rick

terranosaurusdoug · 28-09-2017, 23:03

Quote:

Originally Posted by solarman216

Will take some tomorrow if I remember, the bar or the shelving? I think it is going to be covered with zinc the same as the bar top, with folded joins! Rick

The bar, it looks neat, is it bent round in one piece?

solarman216 · 29-09-2017, 00:43

Quote:

Originally Posted by terranosaurusdoug

The bar, it looks neat, is it bent round in one piece?

Yes one piece of 6mm ply well whetted first, think Dave used 4mm ply for back shelves, the flat sections of the bar will be tiled, the curved section will be zinc, same as bar top, Rick

28-09-2017, 22:33	#73
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,431	Will take some tomorrow if I remember, the bar or the shelving? I think it is going to be covered with zinc the same as the bar top, with folded joins! Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

28-09-2017, 22:07	#72
terranosaurusdoug Senior Member Join Date: Sep 2014 Location: Yorkshire, J33 M62 Vehicle: 2000 Terrano lwb 2.7TDI Posts: 5,500	Any chance of some close ups of the curve round the bar?