Roll Cage

makeitfit · 05-04-2015, 22:27

Can you tell what it is yet ?

don simon · 05-04-2015, 22:29

Removable roof section for the ejector seat?

Sweety · 05-04-2015, 22:42

Either it's a drawing of how your going to do a rear roll cage for the T2 or a poss rear window blank if you turn the Troll into a pick up/ tray back

AlexD333 · 05-04-2015, 22:55

Clueless I'm afraid

makeitfit · 05-04-2015, 22:59

Sweety is nearest

Now what's he going to plump for ?

Sweety · 05-04-2015, 23:06

Quote:

Originally Posted by makeitfit

Sweety is nearest

Now what's he going to plump for ?

I'll go for drawing & template for the rear cage in the Mav

makeitfit · 05-04-2015, 23:15

Bugger, short quiz it is then

don simon · 05-04-2015, 23:23

If it isn't a removable roof section for an ejector seat, it bloody well should be.

makeitfit · 05-04-2015, 23:25

Quote:

Originally Posted by don simon

If it isn't a removable roof section for an ejector seat, it bloody well should be.

It isn't but I'll look into it

AlexD333 · 06-04-2015, 00:08

Quote:

Originally Posted by makeitfit

It isn't but I'll look into it

And to think I stayed up to find out too... I'm off to bed!

*pours coffee away*

makeitfit · 18-04-2015, 20:42

I did a bit more on the roll cage

Sweety · 20-04-2015, 13:09

I forgot all about this

what did I win Pete

interested to see how this comes out

makeitfit · 20-04-2015, 21:26

Your prize is all my experimenting

BBC and all that

Anyway for your prize winning delight , here's this afternoon's mayhem

To cut a long story short I couldn't really get a satisfactory tight bend so went up to the blacksmiths to use his big bender

Unfortunately it kind of broke

In the process got a nasty kink where we didn't want one. He said he'd get me a new length of tube and sort it out. In the end that one got bent in the wrong place , even with my template

Anyroad up , I came away with a load of tube at half price and some internal sleeving.
I did the waist line bends to suit the shell and got this

Internal diameter of the CDS is 40mm as best I could measure it. Got some 40 mm tube with 6mm wall thickness and tried to makeitfit

As you know, a 40mm tube wont fit in a 40mm hole. So after a clean up and a session in the freezer I got this

Then after a bit more polishing got these two parts joined with a 5mm gap for the weld pool.

Plug in one hungry son and then this happened

Now I have the main hoop ready for final tweaking

Here's the weld after a quick clean up

I'm sure some racing rules will say I can't do this but tuff, it's done

It's done in a place where the diagonal will be welded to anyway so in my mind it'll be flippin fine

solarman216 · 20-04-2015, 21:32

What is the diameter of the pipe Pete? looks a bit small to me, Rick

makeitfit · 20-04-2015, 21:43

Quote:

Originally Posted by solarman216

What is the diameter of the pipe Pete? looks a bit small to me, Rick

47.5mm o/d and 3.25mm wall

Seems big enough to me

05-04-2015, 22:27	#1
makeitfit Senior Member Join Date: Apr 2008 Location: on the beach WEST WALES Vehicle: Maverick TDi BLACK mmm Posts: 15,136	Roll Cage Can you tell what it is yet ?

20-04-2015, 21:32	#14
solarman216 Off road maniac Join Date: Dec 2009 Location: Bexhill on Sea Vehicle: Y60 Patrol Me, 3 ltr Mrs Posts: 17,430	What is the diameter of the pipe Pete? looks a bit small to me, Rick __________________ Ex banger racer now off road maniac Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-04-2015, 22:29	#2
don simon Senior Member Join Date: Oct 2014 Location: Gone. Vehicle: Terrano ii Posts: 2,215	Removable roof section for the ejector seat?

05-04-2015, 22:42	#3
Sweety Senior Member Join Date: May 2013 Location: Northumberland Vehicle: Terrano 2.7TDI SE LWB Posts: 3,604	Either it's a drawing of how your going to do a rear roll cage for the T2 or a poss rear window blank if you turn the Troll into a pick up/ tray back

05-04-2015, 22:55	#4
AlexD333 Senior Member Join Date: Jan 2014 Location: Uk Vehicle: 2004 Terrano 2.7 TDI Posts: 7,847	Clueless I'm afraid

05-04-2015, 22:59	#5
makeitfit Senior Member Join Date: Apr 2008 Location: on the beach WEST WALES Vehicle: Maverick TDi BLACK mmm Posts: 15,136	Sweety is nearest Now what's he going to plump for ?

05-04-2015, 23:15	#7
makeitfit Senior Member Join Date: Apr 2008 Location: on the beach WEST WALES Vehicle: Maverick TDi BLACK mmm Posts: 15,136	Bugger, short quiz it is then

05-04-2015, 23:23	#8
don simon Senior Member Join Date: Oct 2014 Location: Gone. Vehicle: Terrano ii Posts: 2,215	If it isn't a removable roof section for an ejector seat, it bloody well should be.

18-04-2015, 20:42	#11
makeitfit Senior Member Join Date: Apr 2008 Location: on the beach WEST WALES Vehicle: Maverick TDi BLACK mmm Posts: 15,136	I did a bit more on the roll cage

20-04-2015, 13:09	#12
Sweety Senior Member Join Date: May 2013 Location: Northumberland Vehicle: Terrano 2.7TDI SE LWB Posts: 3,604	I forgot all about this what did I win Pete interested to see how this comes out

20-04-2015, 21:26	#13
makeitfit Senior Member Join Date: Apr 2008 Location: on the beach WEST WALES Vehicle: Maverick TDi BLACK mmm Posts: 15,136	Your prize is all my experimenting BBC and all that Anyway for your prize winning delight , here's this afternoon's mayhem To cut a long story short I couldn't really get a satisfactory tight bend so went up to the blacksmiths to use his big bender Unfortunately it kind of broke In the process got a nasty kink where we didn't want one. He said he'd get me a new length of tube and sort it out. In the end that one got bent in the wrong place , even with my template Anyroad up , I came away with a load of tube at half price and some internal sleeving. I did the waist line bends to suit the shell and got this Internal diameter of the CDS is 40mm as best I could measure it. Got some 40 mm tube with 6mm wall thickness and tried to makeitfit As you know, a 40mm tube wont fit in a 40mm hole. So after a clean up and a session in the freezer I got this Then after a bit more polishing got these two parts joined with a 5mm gap for the weld pool. Plug in one hungry son and then this happened Now I have the main hoop ready for final tweaking Here's the weld after a quick clean up I'm sure some racing rules will say I can't do this but tuff, it's done It's done in a place where the diagonal will be welded to anyway so in my mind it'll be flippin fine