What tools needed?

AlexD333 · 08-02-2014, 18:16

Just as it's chucking it down i dont want to look. What tools do i need to take off the side steps? Just a ratchet and certain size socket?

It is just the bolts right?

R1cho · 08-02-2014, 18:25

Quote:

Originally Posted by AlexD333

Just as it's chucking it down i dont want to look. What tools do i need to take off the side steps? Just a ratchet and certain size socket?

It is just the bolts right?

yep and they will probably sheer as you undo them

puddle hoppers inc. · 08-02-2014, 18:28

you will be better off tightening them, they will snap any way if you are lucky.

exosteve · 08-02-2014, 18:31

mine unbolted easy.
I put them on ebay for 99p
no sale?
just scrap em

firebobby · 08-02-2014, 18:42

Leave them on or you will look gay

spinna · 08-02-2014, 19:07

My missus wants me to put gay steps back on the Patrol so I've come up with a cunning plan.
Build some rock sliders that'll mount to the chassis and tell her indoors that this way they won't rust away like the gay steps and will be cheaper to make

Sent from my iPhone using Tapatalk

AlexD333 · 08-02-2014, 20:19

Clever. And no, no sale just doing offroading and keep catching em. Theyre still clean at the mo but will be going in the scrap. U reckon tightene em up causing em to snap in? What do they bolt to and is it better if water cant get in?

puddle hoppers inc. · 08-02-2014, 20:32

chasis needs some holes to stop condensation build up and help drainage tbh. whack a load of waxoil or used engine oil in, but be careful where you do it as it will kill your driveway. from my experience of working on my own terry most snap or take hours to undo.

terrano bob · 08-02-2014, 22:43

hi alexd going off all post someone else

AlexD333 · 08-02-2014, 23:11

I'll give em a go tomorrow. My underside was quite rust free so hoping that they will come out with ease

Either way they are coming off!

terrano bob · 08-02-2014, 23:19

that's the way mate go for it

exosteve · 08-02-2014, 23:22

there is always mr angle grinder

rustic · 08-02-2014, 23:24

Quote:

Originally Posted by exosteve

there is always mr angle grinder

And a pair of safety specs.

.

AlexD333 · 08-02-2014, 23:25

Quote:

Originally Posted by terrano bob

that's the way mate go for it

Ahah they must come off, keep catching the bastards. I'm doing some offroad hunting tomorrow in daytime so if I'm lucky I'll take a video of it too.

And then there's me "mr doesn't own an angle grinder"

AlexD333 · 08-02-2014, 23:26

Quote:

Originally Posted by rustic

And a pair of safety specs.

.

Ahaha, I can picture rustic reading the angle grinder comment, then reading my signature n going, hmmmmm

08-02-2014, 18:16	#1
AlexD333 Senior Member Join Date: Jan 2014 Location: Uk Vehicle: 2004 Terrano 2.7 TDI Posts: 7,847	What tools needed? Just as it's chucking it down i dont want to look. What tools do i need to take off the side steps? Just a ratchet and certain size socket? It is just the bolts right?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

08-02-2014, 18:28	#3
puddle hoppers inc. Senior Member Join Date: Dec 2012 Location: west midlands Vehicle: terrano se 2.7 Posts: 1,041	you will be better off tightening them, they will snap any way if you are lucky.

08-02-2014, 18:31	#4
exosteve Senior Member Join Date: Dec 2012 Location: stoke on trent Vehicle: 2001 2.7 td lwb terrano Posts: 2,740	mine unbolted easy. I put them on ebay for 99p no sale? just scrap em

08-02-2014, 18:42	#5
firebobby Senior Member Join Date: Feb 2012 Location: South Bucks Vehicle: Terrano 3.0 SVE 2005 Posts: 3,499	Leave them on or you will look gay

08-02-2014, 19:07	#6
spinna Senior Member Join Date: Dec 2010 Location: Telford, Shropshire Vehicle: Nissan Patrol y60 4.2d Posts: 1,287	My missus wants me to put gay steps back on the Patrol so I've come up with a cunning plan. Build some rock sliders that'll mount to the chassis and tell her indoors that this way they won't rust away like the gay steps and will be cheaper to make Sent from my iPhone using Tapatalk

08-02-2014, 20:19	#7
AlexD333 Senior Member Join Date: Jan 2014 Location: Uk Vehicle: 2004 Terrano 2.7 TDI Posts: 7,847	Clever. And no, no sale just doing offroading and keep catching em. Theyre still clean at the mo but will be going in the scrap. U reckon tightene em up causing em to snap in? What do they bolt to and is it better if water cant get in?

08-02-2014, 20:32	#8
puddle hoppers inc. Senior Member Join Date: Dec 2012 Location: west midlands Vehicle: terrano se 2.7 Posts: 1,041	chasis needs some holes to stop condensation build up and help drainage tbh. whack a load of waxoil or used engine oil in, but be careful where you do it as it will kill your driveway. from my experience of working on my own terry most snap or take hours to undo.

08-02-2014, 22:43	#9
terrano bob Senior Member Join Date: Sep 2013 Location: north west Vehicle: nissan terrano 2 2.7tdi Posts: 1,015	hi alexd going off all post someone else

08-02-2014, 23:11	#10
AlexD333 Senior Member Join Date: Jan 2014 Location: Uk Vehicle: 2004 Terrano 2.7 TDI Posts: 7,847	I'll give em a go tomorrow. My underside was quite rust free so hoping that they will come out with ease Either way they are coming off!

08-02-2014, 23:19	#11
terrano bob Senior Member Join Date: Sep 2013 Location: north west Vehicle: nissan terrano 2 2.7tdi Posts: 1,015	that's the way mate go for it

08-02-2014, 23:22	#12
exosteve Senior Member Join Date: Dec 2012 Location: stoke on trent Vehicle: 2001 2.7 td lwb terrano Posts: 2,740	there is always mr angle grinder