its christmas

exosteve · 12-12-2013, 22:10

well I don't know about you lot but im getting very wound down

Christmas is just around the corner and I cant wait for a two week break.
we haven't had 2 weeks off work since last Christmas.
the last time we had a break was 6th7th of july with fez and co.

its an early pressie and maybe my only one but I like it

zippy656 · 12-12-2013, 22:14

Be better when out the box

exosteve · 12-12-2013, 22:14

upside down in box sorry.
had to mess with it

Lazy-Ferret · 12-12-2013, 22:54

I had my Snorkel and a set of LED Beacons for when we are on call out with the SE4x4R, as my pressy from my wife.

We are going away to Wales for Christmas, so it will be a nice relaxing time for us and the ferrets.

rustic · 12-12-2013, 23:44

It will only show positive boost pressure, it will not show vacuum, well it doesn't on mine, and I tapped into the system, after the Turbo, on my Td.

Sweety · 13-12-2013, 02:49

Quote:

Originally Posted by rustic

It will only show positive boost pressure, it will not show vacuum, well it doesn't on mine, and I tapped into the system, after the Turbo, on my Td.

Didn't on mine either (tdi) & I plumbed in at the turbo

your eyes will be stuck to it for the first few days watching to see when it comes onto boost

elty001 · 13-12-2013, 08:26

it would be nice to start winding down but we have had a breakdown on the overhead crane at work which is awaiting a part coming in from france,so we are nearly a week behind on orders.
the manager asked if we could work 12 hours sat and sun to try and catch up with the back log.
so much for my weekend.it will be nice in the pay packet next week but I would like a bit of time to relax.
on a brighter note the mrs ordered my crimbo pressie yesterday

a snorkel kit for the terrano.

Lazy-Ferret · 13-12-2013, 12:18

Quote:

Originally Posted by elty001

on a brighter note the mrs ordered my crimbo pressie yesterday

a snorkel kit for the terrano.

Snap.... Now if she could just fit it as well....

rustic · 13-12-2013, 12:47

Quote:

Originally Posted by Lazy-Ferret

Snap.... Now if she could just fit it as well....

Well if you don't mind it attached with iron on hemming tape....

elty001 · 13-12-2013, 14:55

Quote:

Originally Posted by Lazy-Ferret

Snap.... Now if she could just fit it as well....

would be nice

I am going to repair my front wing at the same time as I fit this.
cut out the rust and weld a nice new piece back in.

Lazy-Ferret · 13-12-2013, 15:58

Quote:

Originally Posted by rustic

Well if you don't mind it attached with iron on hemming tape....

Suz says what's an Iron?.. and as for the other stuff...

rustic · 13-12-2013, 16:15

Quote:

Originally Posted by Lazy-Ferret

Suz says what's an Iron?.. and as for the other stuff...

It's what you use on white faced, or wood veneered chipboard, to glue on the edging strip.

A pig of a job to get the glue off the iron after... ( should use brown paper between, really...

).
Well so the wife keeps telling me... again and again....

To be fair, I now use an old steam iron, that I took the broken wet bits out of, so it just gets hot now...

micktheshed · 13-12-2013, 17:58

Quote:

Originally Posted by rustic

It will only show positive boost pressure, it will not show vacuum, well it doesn't on mine, and I tapped into the system, after the Turbo, on my Td.

Very true rustic, because there is no throttle plate to obstruct the air intake as per a petrol vehicle (though some diesels do have them). That's why a vacuum pump is required to work the brake servo.
Quite fancy a boost gauge since the 3L is said to be prone to over-boosting if the EGR is blocked off (I intend doing this whan I get the time).
Has anyone fitted a gauge to the 3L, & if so have you any tips regarding source of gauge & fitting.

Barrbeast · 13-12-2013, 22:42

I would check out the patrol4x4 forum bud, the Y61 section on the ZD30 DTI should have all that info. There is a specific section on the ZD30 DTI or just do a search for "boost gauge fitting 3.0" or similar.

Sweety · 19-12-2013, 14:39

Just got my Xmas pressie today

http://www.kenwood-electronics.co.uk...th/KDC-BT92SD/ i'll prob be on for a few hours getting all the settings just right

12-12-2013, 23:44	#5
rustic Senior Member Join Date: Feb 2007 Location: Staffordshire Vehicle: Maverick Mk I 2.7 TD LWB Posts: 7,825	It will only show positive boost pressure, it will not show vacuum, well it doesn't on mine, and I tapped into the system, after the Turbo, on my Td. __________________ Ford Maverick GLX 1995 2.7TD LWB in illusion silver, 98k miles. Owned since new, for 22 years. Best car I have ever owned. Just wish I could drive it more.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

12-12-2013, 22:14	#2
zippy656 Senior Member Join Date: Aug 2008 Location: Devizes Wiltshire Vehicle: Nissan Note Ntec 1.5 Posts: 14,138	Be better when out the box

12-12-2013, 22:14	#3
exosteve Senior Member Join Date: Dec 2012 Location: stoke on trent Vehicle: 2001 2.7 td lwb terrano Posts: 2,740	upside down in box sorry. had to mess with it

12-12-2013, 22:54	#4
Lazy-Ferret Senior Member Join Date: Jun 2012 Location: Sevenoaks, Kent Vehicle: Terrano 2.7TDi SE Touring Posts: 5,221	I had my Snorkel and a set of LED Beacons for when we are on call out with the SE4x4R, as my pressy from my wife. We are going away to Wales for Christmas, so it will be a nice relaxing time for us and the ferrets.

13-12-2013, 08:26	#7
elty001 Senior Member Join Date: Feb 2008 Location: Aflreton,Derbyshire. Vehicle: 2000se+ 2.7tdi terrano II Posts: 6,832	it would be nice to start winding down but we have had a breakdown on the overhead crane at work which is awaiting a part coming in from france,so we are nearly a week behind on orders. the manager asked if we could work 12 hours sat and sun to try and catch up with the back log. so much for my weekend.it will be nice in the pay packet next week but I would like a bit of time to relax. on a brighter note the mrs ordered my crimbo pressie yesterday a snorkel kit for the terrano.

13-12-2013, 22:42	#14
Barrbeast Senior Member Join Date: Mar 2013 Location: Dundee, Scotland Vehicle: 1990 4.2 SWB Safari Posts: 2,615	I would check out the patrol4x4 forum bud, the Y61 section on the ZD30 DTI should have all that info. There is a specific section on the ZD30 DTI or just do a search for "boost gauge fitting 3.0" or similar.

19-12-2013, 14:39	#15
Sweety Senior Member Join Date: May 2013 Location: Northumberland Vehicle: Terrano 2.7TDI SE LWB Posts: 3,604	Just got my Xmas pressie today http://www.kenwood-electronics.co.uk...th/KDC-BT92SD/ i'll prob be on for a few hours getting all the settings just right