|
|
|
|||||||
| Caravan or Towing In this forum you can post anything with regards to caravaning or towing. |
 |
|
|
Thread Tools | Display Modes |
|
|
24-06-2015, 22:08
|
#1 |
|
Senior Member
 Join Date: May 2013
Location: Northumberland
Vehicle: Terrano 2.7TDI SE LWB
Posts: 3,604
|
Cracked caravan window
Went up to the storage site today & found the front window has a crack at the side about an inch long
 I know i'll have to replace it & it's going to cost a few bodily organs but we are planing to go away on Monday so need to do something now to stop it getting any worse. The crack runs from the outer edge towards the seal so was thinking of drilling a very small hole at the end of the crack to try & stop it spreading further over the seal area & into the double glazing part but I would like to try & glue the crack together but not sure what to use A local dealer said super glue & someone else has said to use creeping crack sealer, I will cover the crack & little hole with a thin coat of clear silicone anyway to try & waterproof it a bit
|
|
|
|
24-06-2015, 22:27
|
#2 |
|
Senior Member
Join Date: Sep 2004
Location: UK
Posts: 12,965
|
Wonder if that plastic weld stuff that plumbers use for waste pipes will be any good?
Or melt it together with a soldering iron? |
|
|
|
|
24-06-2015, 22:42
|
#3 |
|
Senior Member
Join Date: May 2013
Location: Northumberland
Vehicle: Terrano 2.7TDI SE LWB
Posts: 3,604
|
Got some epoxy resin but scared in case it just melted the window
it's going to be some time before we have the funds for a new window so wanting to do a nice tidy repair until then
|
|
|
|
|
24-06-2015, 22:49
|
#4 |
|
Senior Member
Join Date: Sep 2004
Location: UK
Posts: 12,965
|
Id be tempted to melt it together with soldering iron and then some fine sand paper.
|
|
|
|
|
24-06-2015, 23:29
|
#5 |
|
Off road maniac
 
Join Date: Dec 2009
Location: Bexhill on Sea
Vehicle: Y60 Patrol Me, 3 ltr Mrs
Posts: 17,431
|
to be honest it is completely insignificant, enjoy your holiday and stop worrying about it, yes drill your hole at the end of the crack to stop it spreading but it is really not a big issue, Rick
__________________
Ex banger racer now off road maniac  Lokka on the front with manual hubs Diff lock on rear 3 inch SS straight through exhaust Manly winch bumper with 13000 lb winch 10 spike ground anchor, with multiple straps and blocks Super strong body cills capped with scaffold pole 20% stronger springs all round aggressive off road tyres on wheels so just swap. Aim to get stuck and be completely self sufficient in extraction, love getting muddy, 2ft deep is good but rare. |
|
|
|
|
25-06-2015, 06:30
|
#6 |
|
Senior Member
Join Date: Sep 2014
Location: Belgium
Vehicle: Terrano II 2.7TDi SWB '97
Posts: 802
|
don't use superglue, as it will leave a white misty film around the glued area. Hole to stop the crack spreading and clear epoxy or silicone should be fine, I think...
|
|
|
|
|
25-06-2015, 09:16
|
#7 | |
|
Moderator
 
Join Date: Jul 2012
Location: West Midlands
Vehicle: 04 2.7 SWB Terrano II Van
Posts: 13,526
|
Quote:
But as Rick said, forget about it then and enjoy the holiday 
__________________
Moderator 04' Terrano II SE 2.7 TDi SWB Commercial in Silver - Project Thread Toyo Open Country M/T 33's on 10J Steels, Super Strong Steering Job Navara D22 Snorkel, Front LOKKA, Maunal Hubs, EGR Blank TunitII ECU Chip, 3" Body Lift, 2" Suss Lift, Heat Exchanger Black Interior, 3.0 Borg&Beck Clutch, Eckes Heated Fuel Filter 99' Y61 Patrol GR SE 2.8 TD6 LWB in Blue/Silver - Project Thread Engine Transplant - In Progress!!! |
|
|
|
|
|
25-06-2015, 09:52
|
#8 |
|
Senior Member
Join Date: Feb 2012
Location: South Bucks
Vehicle: Terrano 3.0 SVE 2005
Posts: 3,499
|
PM sent
|
|
|
|
|
25-06-2015, 12:24
|
#9 |
|
Senior Member
Join Date: May 2013
Location: Northumberland
Vehicle: Terrano 2.7TDI SE LWB
Posts: 3,604
|
Cheers guy's
luckily where the crack is it's mainly silver so any cloudiness shouldn't show up much at all
|
|
|
|
|
|
|
Hybrid Mode
