failed the MOT

geoffdown · 21-10-2013, 19:46

failed on just welding
1. small hole in chassis just in front of tie bar holding rear alxle on to chassis easy fix and
2.two small holes under rear seats
will cost about £1 for metal and a couple of quid for mig wire and gas just aswell i can weld nice easy and cheap fix

makeitfit · 21-10-2013, 19:51

Result, pleased for ya

geoffdown · 21-10-2013, 20:08

Quote:

Originally Posted by makeitfit

Result, pleased for ya

well would of been better with no welding but it is getting old now and i pushed the boat out and got stainless steel sheet at least that wont rust it will be the last thing when the terrano is in the big scrap heap in the sky

just two little patches of stainless

geoffdown · 30-10-2013, 00:40

well managed to get the welding done today so I have 12months and 3ish weeks till next 1

just to let any1 else no when I spoke to the tester bout corrosion around the front body mount the 1 by the steering box as mine has a rusty hole in it he said its not a fail u have to have less than 75% of the body mounts ok any less and its a fail so if the lwb has 10 might be wrong 2 can have rusty holes and not fail

solarman216 · 30-10-2013, 00:51

Quote:

Originally Posted by geoffdown

well managed to get the welding done today so I have 12months and 3ish weeks till next 1

just to let any1 else no when I spoke to the tester bout corrosion around the front body mount the 1 by the steering box as mine has a rusty hole in it he said its not a fail u have to have less than 75% of the body mounts ok any less and its a fail so if the lwb has 10 might be wrong 2 can have rusty holes and not fail

that is interesting and common sense on a T2 as it has a chassis, but would like to see it in writing, Rick

geoffdown · 30-10-2013, 01:29

Quote:

Originally Posted by solarman216

that is interesting and common sense on a T2 as it has a chassis, but would like to see it in writing, Rick

well that's what my tester said to day gave an advisory for the rusty hole o/s/f body mount and he said its in the book saying you got to have 75% or more on the body mounts

Peasgood1 · 30-10-2013, 10:21

Mine failed with two rusty mounting points.

Kishada · 30-10-2013, 17:19

You might want to remind him of Reason for Rejection, Point 2 on this page, extracted straight from the manual.

"Any deliberate modification, excessive corrosion, damage, cracks or inadequate repair of a load bearing body or chassis member which seriously affects its strength within 30cm of the body mountings."

The body mount is a load bearing body member.
Where else is the load of the body being transferred to the chassis other than the mounts?!

21-10-2013, 19:46	#1
geoffdown Senior Member Join Date: Aug 2010 Location: devon Vehicle: terrano 2.7tdi SE+ (X)reg Posts: 1,674	failed the MOT failed on just welding 1. small hole in chassis just in front of tie bar holding rear alxle on to chassis easy fix and 2.two small holes under rear seats will cost about £1 for metal and a couple of quid for mig wire and gas just aswell i can weld nice easy and cheap fix

21-10-2013, 19:51	#2
makeitfit Senior Member Join Date: Apr 2008 Location: on the beach WEST WALES Vehicle: Maverick TDi BLACK mmm Posts: 15,136	Result, pleased for ya

30-10-2013, 00:40	#4
geoffdown Senior Member Join Date: Aug 2010 Location: devon Vehicle: terrano 2.7tdi SE+ (X)reg Posts: 1,674	well managed to get the welding done today so I have 12months and 3ish weeks till next 1 just to let any1 else no when I spoke to the tester bout corrosion around the front body mount the 1 by the steering box as mine has a rusty hole in it he said its not a fail u have to have less than 75% of the body mounts ok any less and its a fail so if the lwb has 10 might be wrong 2 can have rusty holes and not fail

30-10-2013, 10:21	#7
Peasgood1 Senior Member Join Date: Aug 2013 Location: Cheshire Vehicle: '94 swb Terrano Posts: 198	Mine failed with two rusty mounting points.

30-10-2013, 17:19	#8
Kishada Senior Member Join Date: Jun 2012 Location: West Lothian, Scotland Vehicle: Terrano II Posts: 249	You might want to remind him of Reason for Rejection, Point 2 on this page, extracted straight from the manual. "Any deliberate modification, excessive corrosion, damage, cracks or inadequate repair of a load bearing body or chassis member which seriously affects its strength within 30cm of the body mountings." The body mount is a load bearing body member. Where else is the load of the body being transferred to the chassis other than the mounts?!