Silence is Golden, dumped the drop links

jims-terrano · 16-09-2018, 20:41

Oh man what a difference, removed the front anti roll bar links on the project truck today and fitted rose joints instead.
Tooks Solarmans advice from a while back and removed anti roll bar to fit the new links, makes it far easier to tighten them up properly. To remove the anto roll bar clamps I used Rustics advice of losen tighten the stubborn nuts.

Job done and much better, teouble is I can hear every other knocks and rattles now

Did find time to replace the bolts holding the aluminium plate on the side steps which is a whole lot better too.

elty001 · 16-09-2018, 21:50

Sounds like you've had a productive day Jim

Its a good feeling to sort out these little jobs,well done mate!!!

Davey Boy · 16-09-2018, 22:26

A productive weekend Jim.
That's a few jobs off the list.

jonny · 16-09-2018, 23:50

Where did you get those from Jim.? My MOT is due soon and there is quite a bit to do and this is one of the jobs.

Cheers

jims-terrano · 17-09-2018, 06:49

I bought them ages ago from bigbunny, sounds bad

.

If you do a search on here there was a thread ages ago which I think it was Makeitfit, Banshee and Elty were sourcing them. I was going to see how these perform before trying to source another set for the other truck.

jonny · 17-09-2018, 09:43

Cheers Jim, I shall have a look

16-09-2018, 20:41	#1
jims-terrano Senior Member Join Date: Sep 2004 Location: UK Posts: 12,965	Silence is Golden, dumped the drop links Oh man what a difference, removed the front anti roll bar links on the project truck today and fitted rose joints instead. Tooks Solarmans advice from a while back and removed anti roll bar to fit the new links, makes it far easier to tighten them up properly. To remove the anto roll bar clamps I used Rustics advice of losen tighten the stubborn nuts. Job done and much better, teouble is I can hear every other knocks and rattles now Did find time to replace the bolts holding the aluminium plate on the side steps which is a whole lot better too.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

16-09-2018, 21:50	#2
elty001 Senior Member Join Date: Feb 2008 Location: Aflreton,Derbyshire. Vehicle: 2000se+ 2.7tdi terrano II Posts: 6,832	Sounds like you've had a productive day Jim Its a good feeling to sort out these little jobs,well done mate!!!

16-09-2018, 22:26	#3
Davey Boy Senior Member Join Date: Dec 2015 Location: Dartmoor Vehicle: Patrol ZD30 SVE Posts: 960	A productive weekend Jim. That's a few jobs off the list.

16-09-2018, 23:50	#4
jonny Senior Member Join Date: Jan 2018 Location: Cheshire Vehicle: Terrano Posts: 198	Where did you get those from Jim.? My MOT is due soon and there is quite a bit to do and this is one of the jobs. Cheers

17-09-2018, 06:49	#5
jims-terrano Senior Member Join Date: Sep 2004 Location: UK Posts: 12,965	I bought them ages ago from bigbunny, sounds bad . If you do a search on here there was a thread ages ago which I think it was Makeitfit, Banshee and Elty were sourcing them. I was going to see how these perform before trying to source another set for the other truck.

17-09-2018, 09:43	#6
jonny Senior Member Join Date: Jan 2018 Location: Cheshire Vehicle: Terrano Posts: 198	Cheers Jim, I shall have a look