Mig Welder Gas Kit

jims-terrano · 28-06-2015, 18:19

Does anyone know where I can get a gas kit for a Kende Mag 150r mig welder?

It's gas and gas less but theres no gas equipment with it, works perfectly well as a gas less mig but for doing bodywork Id rather have co2.

Fez_uk · 28-06-2015, 18:39

You just need the bottle and regulator then?

Rent free gas bottle supplier I use: http://www.sgsgases.co.uk/mig-tig-welding

jims-terrano · 28-06-2015, 18:46

Don't I need to do pwt to the torch and tip or anything?

Fez_uk · 28-06-2015, 18:52

It should have it all installed if it's advertised as a gas or gasless.

You will have to change the polarity of the torch and clamp, Read this: http://www.mig-welding.co.uk/forum/t...ag-150r.26399/

jims-terrano · 28-06-2015, 19:33

Ok I see how it works and yes it has an opaque white tube going from the gas connector out to the torch, so that means exactly as you say Fez all I need is a reg and bottle oh and a bit of tube.

So the rolls of wire that are with it say this on the boxes, can this be used with gas or is it only gas less using that wire?

Self Shielded Flux Cored Wire

Thanks

Fez_uk · 28-06-2015, 19:57

Thats gasless, So you will also have to buy new wire

28-06-2015, 18:19	#1
jims-terrano Senior Member Join Date: Sep 2004 Location: UK Posts: 12,965	Mig Welder Gas Kit Does anyone know where I can get a gas kit for a Kende Mag 150r mig welder? It's gas and gas less but theres no gas equipment with it, works perfectly well as a gas less mig but for doing bodywork Id rather have co2.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

28-06-2015, 18:39	#2
Fez_uk Senior Member Join Date: Sep 2010 Location: Mid-Wales Vehicle: Maverick 2.7 - Patrol 4.2 Posts: 5,645	You just need the bottle and regulator then? Rent free gas bottle supplier I use: http://www.sgsgases.co.uk/mig-tig-welding

28-06-2015, 18:46	#3
jims-terrano Senior Member Join Date: Sep 2004 Location: UK Posts: 12,965	Don't I need to do pwt to the torch and tip or anything?

28-06-2015, 18:52	#4
Fez_uk Senior Member Join Date: Sep 2010 Location: Mid-Wales Vehicle: Maverick 2.7 - Patrol 4.2 Posts: 5,645	It should have it all installed if it's advertised as a gas or gasless. You will have to change the polarity of the torch and clamp, Read this: http://www.mig-welding.co.uk/forum/t...ag-150r.26399/

28-06-2015, 19:33	#5
jims-terrano Senior Member Join Date: Sep 2004 Location: UK Posts: 12,965	Ok I see how it works and yes it has an opaque white tube going from the gas connector out to the torch, so that means exactly as you say Fez all I need is a reg and bottle oh and a bit of tube. So the rolls of wire that are with it say this on the boxes, can this be used with gas or is it only gas less using that wire? Self Shielded Flux Cored Wire Thanks

28-06-2015, 19:57	#6
Fez_uk Senior Member Join Date: Sep 2010 Location: Mid-Wales Vehicle: Maverick 2.7 - Patrol 4.2 Posts: 5,645	Thats gasless, So you will also have to buy new wire